Official Blumat Distributors for the United States                     |   FREE Shipping Over $100

Black Friday Sale
Black Friday Sale

BluSoak Kits

BluSoak-gravity-irrigation-benefits

BluSoak solves a major irrigation challenge - providing an automated, extremely low-cost solution without requiring commercial pressure, a pump, or a very high reservoir. Perfect for watering with only gravity, you only need about 1 psi.

In backyards, best to use on the surface with a deep mulch; in commercial and large scale applications, it could be the key to realistically developing true regenerative irrigation systems.

These kits provide an easy, fast, and water-saving way to water garden beds, either raised or in your garden. No timers, batteries, or electricity required! BluSoak tape allows for even water distribution throughout the entire bed, as the entire length of BluSoak drip tape releases water. When coupled together with Blumat carrots, BluSoak hose only delivers water to your plants when they need it, which promotes exponential growth and impressive yields. You can also leave your BluSoak tape under your garden all winter, no problem. Water source needs to be above the garden for a gravity system. For a pressure system running off a faucet or garden hose, simply add a Blumat Pressure Reducer

7 products


  • BluSoak tape fitting w/ 5" Sensor Carrot Set-1

    BluSoak tape fitting w/ 5" Sensor Carrot Set

    Description Set for connecting a Blumat sensor to BluSoak 2.0 Drip Tape. Easy convenient way to setup a BluSoak system, all you need is the amount of BluSoak soaker hose you need, and either another BluSoak to Sensor set or a BluSoak end plug fitting. Components The Set includes: 1 5" Tropf Blumat (IG19079) 1 Distribution Dripper (IG15565) 1 Distribution Dripper Stake (IG16314) 1 BluSoak to 3mm Adapter (IG16085)

    $15.75

  • Garden BluSoak Kit, 100'-1

    Garden BluSoak Kit, 100'

    This kit include 100 feet of BluSoak (IG18206)

    $111.14

  • 5-Gallon Reservoir w/8mm Bulkhead and Float Valve

    5-Gallon Reservoir w/8mm Bulkhead and Float Valve

    Keep your gravity-fed watering system running hands-free. This 5-gallon reservoir is designed to work as the water source for Inline Classic drippers or BluSoak gravity drip tape — automatically maintaining a steady supply so your plants get what they need without manual refilling. What's Included + 5-gallon reservoir with pre-drilled holes for bulkhead and float valve One 8mm bulkhead fitting Float valve Swivel adapter for standard garden hose connection How It Works + Connect your garden hose to the swivel adapter. The float valve automatically maintains the water level in the reservoir — when the level drops, it refills. From there, your Inline Classic drippers or BluSoak gravity drip tape deliver water directly to plant roots on demand. Completely plant-responsive. No timers, no electricity, no manual refilling. Compatible With + Inline Classic drippers BluSoak gravity drip tape Any gravity-fed Blumat or BluSoak system requiring a constant-level reservoir

    $64.80

  • 4'x12' Blusoak Double Manifold

    4'x12' Blusoak Double Manifold

    Description This kit provides an easy, fast, and water-saving way to water a 4ft by 12ft bed, either raised or in your garden. No timers, batteries, or electricity required! This system utilizes Blumat carrots (sensor) to automatically water and monitor the moisture levels in your garden soil. BluSoak tape allows for even water distribution throughout. When coupled together with Blumat carrots, BluSoak hose only delivers water to your veggies when they need it, which promotes exponential growth and impressive yields. You can also leave your BluSoak tape under your garden all winter, no problem. Water source needs to be 6-10' above the garden for a gravity system. For a pressure system running off a faucet or garden hose, simply add a Blumat Pressure Reducer. What You Might Need (Not included in kit): Connection to your water source (either thru-hull bulkhead fitting for gravity systems, a pressure reducer, or a Blumat pump for larger systems) 8mm Supply tube to connect your water source to your Blumats Additional Hold-Down stakes or 3mm tubing Fittings (tee's, elbows, couplers, etc.) Reservoir- See our 5 gallon bucket reservoirs Want more information? Here's a guide to Grassroots Raised Bed. Components This Kit Includes: 44 feet of BluSoak 2.0 Drip Tape (IG18206) 4 x Blumat 8mm Elbow (IG15595) 4 x Blumat 8mm Tee (IG15581) 1 x Blumat Maxi Long Sensor (IG14607) 1 x Blumat Standard 5" Sensor (IG14618) 8 x BluSoak to 8mm Adapter (AG15807) 2 x Blumat 8mm to 3mm Reducing Tee (IG15476) 8 feet of 8mm Super-Flex Tubing (IG15634) 6 feet of 3mm Drip Tube (IG15473V) Click here to download the instructions.

    $104.37

  • Sale -15% High-Pressure BluSoak black tape in a raised bed

    High-Pressure BluSoak Raised Bed Kits

    High-Pressure BluSoak Raised Bed Kits pair a preset 9" Blumat sensor with ultra-low-flow, emitter-style High-Pressure BluSoak drip tape. The 6-inch emitter spacing promotes continuous lateral wicking and uniform moisture across raised beds and large containers. Designed exclusively for pressurized installations operating between 10 and 15 PSI. These kits require a regulated hose bib or pump system and will not operate correctly from gravity pressure. Formerly described as BluSoak 3.0 high-pressure kits. The removable straight-line layout makes the system easy to lift out, amend beneath, and reinstall between cycles. Pressure & Water Source Requirements + Required operating pressure: 10–15 PSI Works with a regulated hose bib, municipal supply, or pump system Use a 1-bar (15 PSI) reducer or an adjustable pressure reducer set within the operating range Not compatible with gravity-fed systems The pump, hose connection, pressure reducer, and main supply line are not included. Kit Options + 2×4 Bed / Large Container — Two straight runs and 10 ft of High-Pressure BluSoak 4×4 Bed — Four straight runs and 20 ft of High-Pressure BluSoak 4×8 Bed — Four straight runs and 40 ft of High-Pressure BluSoak What's Included + Preset 9" Blumat sensor High-Pressure BluSoak drip tape with 6-inch emitter spacing 8mm SuperFlex header lines Required in-bed BluSoak fittings and adapters What You'll Also Need + This kit covers the irrigation components inside the bed. To complete the system, you will also need: An 8mm supply line running from the water source to the Blumat sensor A pressurized water source such as a hose bib or pump A compatible pressure reducer set between 10 and 15 PSI Straight-Line Layout + Lift the irrigation assembly out before amending the bed Reinstall it without rebuilding a woven layout Keep the tape runs clean, modular, and easy to service Maintain consistent pressure distribution through header-fed straight runs How It Works + The preset Blumat sensor responds continuously to soil moisture and controls water flow into the tape. As the bed dries, the sensor opens. When the target moisture level is restored, it closes automatically. High-Pressure BluSoak releases water from closely spaced emitters. At 10–15 PSI, the low flow rate and 6-inch spacing create stable, predictable moisture distribution without relying on a timer. Installation Notes + Cut the tape directly through an emitter, not between emitters. Position the first emitter approximately 6 inches from the fitting. Fully tighten all tape fittings; even small leaks can reduce pressure and cause uneven performance. Purge the supply line and confirm full finished-system pressure before calibrating or adjusting the sensor. Frequently Asked QuestionsWhich water source should I use? Use a hose bib or pump regulated to 10–15 PSI. Choose a Blumat-compatible 15 PSI reducer or an adjustable reducer set within that range. A 7.25 PSI reducer does not provide enough pressure. What is sold separately? The water source and main supply line are sold separately. High-pressure installations also require a compatible pressure reducer. Is this the same tape as BluSoak 3.0? Yes. BluSoak 3.0 is now High-Pressure BluSoak. The new name clarifies which water setup to use.Optional: add mulch control The included 9-inch preset sensor controls moisture deeper in the bed. For mulch control, add a separate 5-inch preset sensor. It is optional and sold separately. View the 5-inch preset sensorHigh-Pressure BluSoak Drip Tape · Compare raised bed watering kits · Build a complete irrigation system · Preset Blumat setup instructions High-Pressure BluSoak cutting and fitting instructions. Select the image to enlarge.

    $35.70 - $59.50

  • Sale -15% Gravity BluSoak white tape in a raised bed

    Gravity BluSoak Raised Bed Kits

    Gravity BluSoak Raised Bed Kits pair a preset 9-inch Blumat sensor with white, porous BluSoak tape. The sensor controls watering automatically as the soil dries and moistens. Choose your bed size—every kit includes the preset sensor. For an elevated gravity reservoir. No pump, timer, or electricity is required. The reservoir and main supply line are sold separately. Bed Size & Layout+ 2 × 4 feet: two rows of Gravity BluSoak tape. 4 × 4 feet: four rows of Gravity BluSoak tape. 4 × 8 feet: four rows of Gravity BluSoak tape. What's Included+ One preset 9-inch Blumat sensor White Gravity BluSoak tape sized for the selected bed Required in-bed fittings and adapters 3mm drip tubing Preset locking cap, 3mm union, and adjustment key Water Source & Supply Line+ Connect to an elevated reservoir using an 8mm supply line. Position the bottom of the reservoir approximately 3½ feet or more above the soil surface. The reservoir and main supply line are not included. Do not connect white Gravity BluSoak tape to a 7.25 PSI or 15 PSI pressure reducer; excessive pressure can damage the tape. Using a hose bib or pump? Choose the High-Pressure BluSoak Raised Bed Kit. How It Works+ As the soil dries, the preset Blumat sensor opens and sends water into the tape. When the target moisture level returns, the sensor closes. The white tape is porous along its length, releasing water across the bed rather than from individual emitter points. Optional: add mulch control The included 9-inch preset sensor controls moisture deeper in the bed. For mulch control, add a separate 5-inch preset sensor. It is optional and sold separately. View the 5-inch preset sensorPreset sensor setup instructions · Compare raised bed kits · Build a complete system Looking for another sensor or layout? Choose your layout, sensor length, and preset or standard adjustment. Build your own bed kit →

    $40.39 - $69.77

  • Sale -15% Gravity BluSoak white tape in a raised bed

    BluSoak Raised Bed Kits — Gravity or High Pressure

    Choose your bed size, then choose Gravity or High Pressure. Every BluSoak Raised Bed Kit includes a preset 9-inch Blumat sensor, distribution tape sized for the bed, and the fittings needed inside the bed. The sensor responds to soil moisture, opening the water flow as the soil dries and closing it as moisture returns. No watering timer is required. The water source, pressure reducer, and main supply line are sold separately. Beds and growing media shown in the photos are not included. Gravity or High Pressure? Gravity: White, porous Gravity BluSoak tape for an elevated reservoir. Water seeps along the tape. Do not connect this tape to a 7.25 PSI or 15 PSI pressure reducer. High Pressure: Black, emitter-style BluSoak tape for a regulated hose bib or pump. Use a compatible 15 PSI Blumat pressure reducer or an adjustable reducer set for High-Pressure BluSoak. A 7.25 PSI reducer is not suitable. Choose the version that matches your water source. The two tape types have different pressure requirements. Choose your bed size 2 × 4 feet 4 × 4 feet 4 × 8 feet Each size is available in Gravity and High Pressure. Every selection includes a preset 9-inch sensor. What's included One preset 9-inch Blumat sensor The selected Gravity or High-Pressure BluSoak tape, sized for your bed Required in-bed fittings and adapters 3mm drip tubing Complete your watering system Connect the sensor to your water source using an 8mm supply line. Gravity requires an elevated reservoir; High Pressure requires a regulated hose bib or pump. Preset sensor setup instructions · Compare raised bed watering kits Browse the individual Gravity and High-Pressure kits, or build your own bed kit for other sensor and layout options. Optional: add mulch control The included 9-inch preset sensor controls moisture deeper in the bed. For mulch control, add a separate 5-inch preset sensor. It is optional and sold separately. View the 5-inch preset sensor Looking for another sensor or layout? For more gravity-fed configurations, choose your layout, sensor length, and preset or standard adjustment. Shop all configurations → Compare all Gravity and High-Pressure bed kits →

    $35.70 - $69.77

Login

Forgot your password?

Don't have an account yet?
Create account