Blumat Pressure Reducers

Description TRUE REDUCER - Not a mere flow controller, this brings water pressure down to 15 PSi (1 bar)! EASY TO INSTALL - Screws onto standard hose thread (3/4" input), and ouputs to 8mm tubing! ENDURING - Made from ABS plastic and designed with few points of failure, this is built to last! BLUMAT-READY - Designed specifically for blumat watering systems and 8mm tubing, no tools necessary! AUSTRIAN-ENGINEERED - This high-quality component is designed and manufactured by clever Austrians!   Blumat systems need low pressure, much less than comes from normal house water connections. The blumat Pressure Reducer allows for easy integration of a municipal (or otherwise pressurized line, such as from a well) water line into a blumat, blusoak, or easysoak watering system. BEWARE IMPOSTERS! Many pressure reducers are not real pressure reducers at all, but are merely flow controllers, and reduce flow rates. However, reduced flow rates DO NOT necessarily correlate to reduced pressures. This is a true pressure reducer, and will reduce any incoming water (with a maximum pressure input of 87PSi) down to a 15PSi (1 bar) output. This is ideally suited and low enough for blumat systems and their components. Higher pressure will push tubing connections apart, and increase likelihood of flooding. This pressure reducer is extremely easy to use. The input side screws onto a standard 3/4" hose bibb or hose threading, often found on taps outside the home, or even faucets inside the home. The output side (featured with collar) is ideally suited for 8mm tubing (I suggest using our super-flex tubing). This is the size that integrates directly with tropf blumats. This adaptation makes setting up a blumat system from a hose or pressurized line an absolute breeze, and you can install your blumats in seconds. Blumat systems need low pressure, much less than comes from normal house water connections. Some of our kits include one of these but if you'd like to install the other ones or the separate components to a home water system, you'll need one of these Pressure Reducers. In gravity systems you'll also need one if your storage tank is high uphill. In Grow Rooms and Greenhouses with a reservoir for mixing nutrients, you can connect a small pressure pump to this and automatically feed your plants when you water. On one side it adapts to a 3/4" male hose thread and on the other directly to the Blumat 8 mm supply tube. Maximum input pressure is 87 psi.

Read more less

Description True reducer - Not a mere flow controller, this brings water pressure down to 7.25 psi (0.5 bar)! Easy to install - Screws onto standard hose thread (3/4" input), and outputs to 8mm tubing! Enduring - Made from ABS plastic and designed with few points of failure, this is built to last! Blumat ready - Designed specifically for Blumat water systems and 8mm tubing, no tools necessary! Austria-engineered - This is high-quality component and is designed and manufactured by clever Austrians! Blumat systems need low pressure, much less than comes from a normal house water connections. The Blumat Pressure Reducer allows for easy integration of a municipal (or otherwise pressurized line, such as from a well) water line into a blumat, blusoak, or easysoak watering system. Beware imposters! Many pressure reducers are not real pressure reducers at all, but are merely flow controllers, and reduce flow rates. However, reduced flow rates do not necessarily correlate to reduced pressure. This is a true pressure reducer, and will reduce any incoming water (with a maximum pressure input of 87 psi) down to 7.25i (0.5 bar) output. This is ideally suited and low enough for Blumat systems and their components. Higher pressure will push tubing connections apart, and increase likelihood of flooding. This pressure reducer is extremely easy to use. The input side screws onto a standard 3/4") hose bibb or hose threading, often found on taps outside the home, or even faucets inside the home. The output side (featured with collar) is ideally suited for 8mm tubing (I suggest using our super-flex tubing). This is the size that integrates directly with Tropf Blumats. This adaptation makes setting up a Blumat system from a hose or pressurized line an absolute breeze, and you can install blumats in seconds. Blumat systems need low pressure, much less than comes from a normal house water connections. Some of our kits include one of these but if you'd like to install the other ones or the separate components to a home water system, you'll need one of these Pressure Reducers. In gravity systems you'll also need one if your storage tank is high uphill. In Grow Rooms and Greenhouses with a reservoir for mixing nutrients, you can connect a small pressure pump to this and automatically feed your plants when you water. On one side it adapts to a 3/4" male hose thread and on the other directly to a Blumat 8mm supply tube. Maximum input pressure is 87 psi.

Read more less

Inexpensive but accurate and adjustable, this pressure reducer lets you adjust the input pressure of a Blumat system from between 1 and 14 psi - you can uniformly modify moisture levels of your entire garden with the turn of a single dial. Lower the pressure for dryer soil, raise it to keep it more moist. Because you can adjust all the Blumat sensors in your system from a single point, the more plants you have, the more time you save. And  its high 5 GPM flow capacity means more consistency and even output. 0-30 psi gauge, 3/4" FPT swivel input, output options 1/2" FPT, 8 mm barb, or 1/2" Perma-loc.

Read more less

Description TRUE REDUCER - Not a mere flow controller, this brings water pressure down to 15 PSi (1 bar)! EASY TO INSTALL - Screws onto standard hose thread (3/4" input), and ouputs to 8mm tubing! ENDURING - Made from ABS plastic and designed with few points of failure, this is built to last! BLUMAT-READY - Designed specifically for blumat watering systems and 8mm tubing, no tools necessary! AUSTRIAN-ENGINEERED - This high-quality component is designed and manufactured by clever Austrians!   Blumat systems need low pressure, much less than comes from normal house water connections. The blumat Pressure Reducer allows for easy integration of a municipal (or otherwise pressurized line, such as from a well) water line into a blumat, blusoak, or easysoak watering system. BEWARE IMPOSTERS! Many pressure reducers are not real pressure reducers at all, but are merely flow controllers, and reduce flow rates. However, reduced flow rates DO NOT necessarily correlate to reduced pressures. This is a true pressure reducer, and will reduce any incoming water (with a maximum pressure input of 87PSi) down to a 15PSi (1 bar) output. This is ideally suited and low enough for blumat systems and their components. Higher pressure will push tubing connections apart, and increase likelihood of flooding. This pressure reducer is extremely easy to use. The input side screws onto a standard 3/4" hose bibb or hose threading, often found on taps outside the home, or even faucets inside the home. The output side (featured with collar) is ideally suited for 8mm tubing (I suggest using our super-flex tubing). This is the size that integrates directly with tropf blumats. This adaptation makes setting up a blumat system from a hose or pressurized line an absolute breeze, and you can install your blumats in seconds. Blumat systems need low pressure, much less than comes from normal house water connections. Some of our kits include one of these but if you'd like to install the other ones or the separate components to a home water system, you'll need one of these Pressure Reducers. In gravity systems you'll also need one if your storage tank is high uphill. In Grow Rooms and Greenhouses with a reservoir for mixing nutrients, you can connect a small pressure pump to this and automatically feed your plants when you water. On one side it adapts to a 3/4" male hose thread and on the other directly to the Blumat 8 mm supply tube. Maximum input pressure is 87 psi.

Read more less

Description TRUE REDUCER - Not a mere flow controller, this brings water pressure down to 15 PSi (1 bar)! EASY TO INSTALL - Screws onto standard hose thread (3/4" input), and ouputs to 8mm tubing! ENDURING - Made from ABS plastic and designed with few points of failure, this is built to last! BLUMAT-READY - Designed specifically for blumat watering systems and 8mm tubing, no tools necessary! AUSTRIAN-ENGINEERED - This high-quality component is designed and manufactured by clever Austrians!   Blumat systems need low pressure, much less than comes from normal house water connections. The blumat Pressure Reducer allows for easy integration of a municipal (or otherwise pressurized line, such as from a well) water line into a blumat, blusoak, or easysoak watering system. BEWARE IMPOSTERS! Many pressure reducers are not real pressure reducers at all, but are merely flow controllers, and reduce flow rates. However, reduced flow rates DO NOT necessarily correlate to reduced pressures. This is a true pressure reducer, and will reduce any incoming water (with a maximum pressure input of 87PSi) down to a 15PSi (1 bar) output. This is ideally suited and low enough for blumat systems and their components. Higher pressure will push tubing connections apart, and increase likelihood of flooding. This pressure reducer is extremely easy to use. The input side screws onto a standard 3/4" hose bibb or hose threading, often found on taps outside the home, or even faucets inside the home. The output side (featured with collar) is ideally suited for 8mm tubing (I suggest using our super-flex tubing). This is the size that integrates directly with tropf blumats. This adaptation makes setting up a blumat system from a hose or pressurized line an absolute breeze, and you can install your blumats in seconds. Blumat systems need low pressure, much less than comes from normal house water connections. Some of our kits include one of these but if you'd like to install the other ones or the separate components to a home water system, you'll need one of these Pressure Reducers. In gravity systems you'll also need one if your storage tank is high uphill. In Grow Rooms and Greenhouses with a reservoir for mixing nutrients, you can connect a small pressure pump to this and automatically feed your plants when you water. On one side it adapts to a 3/4" male hose thread and on the other directly to the Blumat 8 mm supply tube. Maximum input pressure is 87 psi.

Read more less

DescriptionThis is a 15 Psi Blumat Pressure Reducer that has all of the fittings and adapters to allow you to fit this into 1/4" supply tube with 8mm on the output.Great for being able to get optimal pressure for your Blumat System, but can now be implemented into your existing 1/4" drip system so that you can get the optimal pressure from your own supply line, then lead into the 8mm tubing from that main line.

Read more less

DescriptionThis is a 15 Psi Blumat Pressure Reducer that has all of the fittings and adapters to allow you to fit this into 1/2" tubing ideal for PVC, PolyPipe, Drip Tube, PEX, etc. Great for being able to get optimal pressure for your Blumat System, but can now be implemented into your existing 1/2" pipe so that you can get the optimal pressure from your own supply line, then lead into the 8mm tubing from that main line.Got multiple rooms running a Blumat system? Integrate this 1/2" Blumat Pressure Reducer into the main water supply line before going into each individual room.

Read more less

DescriptionThe standard Blumat pressure reducers work great for most systems. But for larger systems that need a higher flow rate, this becomes a better choice. This also works better when there's a long distance between the pressure reducer and your plants.A TRUE REDUCER - Not just a flow controller that only works with high flows, these reduce pressure in Blumat systems with extremely low flow ratesEASY TO INSTALL - Uses standard 3/4"" hose thread for both input and ouput sidesHIGH QUALITY - Built to last from ABS plastic and designed for longest life Blumat systems need constant low pressure — much less than municipal home and farm pressure. These reducers insure a constant pressure.Often, people call flow restrictors "pressure reducers" and they can reduce pressure — but only if the system has a high flow. These true pressure reducers take input an pressure up to 87 psi and drop it down to 15 psi (1 bar) output. Ideally suited for Blumat and other drip irrigation systems, lowering the pressure also prevents tubing connections from coming apart and creating a flood. In gravity systems, you don't need a reducer unless you have a storage tank high up a hill, 35' or more vertical. Horizontal distance doesn't make much difference."3/4" Female Hose Thread input, 3/4" Male Hose Thread output, Max pressure in 87 psi, output pressure limited at 15 psi maxA TRUE REDUCER - Not just a flow controller that only works with high flows, these reduce pressure in Blumat systems with extremely low flow ratesEASY TO INSTALL - Uses standard 3/4" hose thread for both input and ouput sidesHIGH QUALITY - Built to last from ABS plastic and designed for longest life Blumat systems need constant low pressure — much less than municipal home and farm pressure. These reducers insure a constant pressure.Often, people call flow restrictors "pressure reducers" and they can reduce pressure — but only if the system has a high flow. These true pressure reducers take input an pressure up to 87 psi and drop it down to 15 psi (1 bar) output. Ideally suited for Blumat and other drip irrigation systems, lowering the pressure also prevents tubing connections from coming apart and creating a flood. In gravity systems, you don't need a reducer unless you have a storage tank high up a hill, 35' or more vertical. Horizontal distance doesn't make much difference.3/4" Female Hose Thread input, 3/4" Male Hose Thread output, Max pressure in 87 psi, output pressure limited at 15 psi max

Read more less

DescriptionLike our standard Blumat Pressure Reducer but with 3/4"" hose thread output!The standard Blumat pressure reducers work great for most systems. But for larger systems that need a higher flow rate, this becomes a better choice. This also works better when there's a long distance between the pressure reducer and your plants.A TRUE REDUCER - Not just a flow controller that only works with high flows, these reduce pressure in Blumat systems with extremely low flow ratesEASY TO INSTALL - Uses standard 3/4"" hose thread for both input and ouput sidesHIGH QUALITY - Built to last from ABS plastic and designed for longest life Blumat systems need constant low pressure — much less than municipal home and farm pressure. These reducers insure a constant pressure.Often, people call flow restrictors "pressure reducers" and they can reduce pressure — but only if the system has a high flow. These true pressure reducers take input an pressure up to 87 psi and drop it down to 7.5 psi (.5 bar) output. Ideally suited for Blumat and other drip irrigation systems, lowering the pressure also prevents tubing connections from coming apart and creating a flood. In gravity systems, you don't need a reducer unless you have a storage tank high up a hill, 35' or more vertical. Horizontal distance doesn't make much difference.3/4" Female Hose Thread input, 3/4" Male Hose Thread output, Max pressure in 87 psi, output pressure limited at 7.5 psi max

Read more less

DescriptionReplacement screen for the input side of a Blumat brand 15psi pressure reducer.

Read more less

DescriptionDesigned to be inserted into a 1/2" poly line.

Read more less

Description This a pressure reducer used for if you need a higher pressure due to having a longer distance going from your hose bib to your plants, or if your water supply is going up so you need a little extra pressure to bring it up vertically. Blumat systems need low pressure, much less than comes from normal house water connections. Some of our kits include a pressure reducer but if you'd like to install the other ones or the separate components to a home water system, you'll need one of these Pressure Reducers. In gravity systems you'll also need one if your storage tank is high uphill. In Grow Rooms and Greenhouses with a reservoir for mixing nutrients, you can connect a small pressure pump to this and automatically feed your plants when you water. On one side it adapts to a 3/4" male hose thread and on the other directly to the Blumat 8 mm supply tube. For BluSoak Systems, use a our 0.5bar Pressure Reducer (7psi) as our BluSoak doesn't like pressure over 10psi and can even split. Or use one of these and a flow restrictor alternatively.

Read more less