Blumat Raised Bed Watering Kits

Gravity BluSoak Raised Bed Kits provide automatic, soil-moisture-controlled irrigation for raised beds using porous Gravity BluSoak drip tape. The entire length of the tape releases water slowly and evenly, while the Blumat sensor starts and stops the flow based on the moisture in the soil. Designed for gravity-fed Blumat irrigation systems. Use an elevated reservoir. Do not connect this white porous tape to a 7.25 PSI or 15 PSI pressure reducer. Formerly described as BluSoak 2.0 raised-bed kits. No timer, electricity, or programming is required. Pressure & Water Source Requirements ＋ Gravity BluSoak is intended for gravity-fed systems. The 7.25 PSI and 15 PSI pressure reducers are not compatible; excessive pressure can damage the tape. Gravity reservoir: Position the bottom of the reservoir approximately 3½ feet or more above the soil surface to provide adequate pressure. The reservoir, pump, hose connection, pressure reducer, and main supply line are not included . Bed Size & Layout ＋ 2 Row (2×4 ft) — Two rows of Gravity BluSoak drip tape 3 Row (3×3 ft) — Three rows of Gravity BluSoak drip tape 3 Row (3×6 ft) — Three rows of Gravity BluSoak drip tape 4 Row (4×4 ft) — Four rows of Gravity BluSoak drip tape 4 Row (4×8 ft) — Four rows of Gravity BluSoak drip tape Sensor Type ＋ 5" Sensor — Best for shallow beds and sensing moisture nearer the soil surface. 9" Sensor — Better for deeper beds and monitoring moisture farther into the root zone. 5" + 9" Dual Sensor — Uses two sensing depths to control the bed together. Calibration Type ＋ Standard — Ships with the standard Blumat adjustment top for you to calibrate after installation. Preset — Pre-calibrated at our Colorado warehouse and includes a locking adjustment cap, 3mm union, and adjustment key. What's Included ＋ Blumat sensor or sensors based on your selection Gravity BluSoak drip tape sized for the selected bed layout Required in-bed BluSoak fittings and adapters 3mm drip tubing Preset selections also include the locking cap, 3mm union, and adjustment key What You'll Also Need ＋ This kit covers the irrigation components inside the bed. To complete the system, choose: 8mm supply line running from the water source to the Blumat sensor A gravity reservoir with an 8mm bulkhead connection How It Works ＋ The Blumat sensor continuously responds to soil moisture. As the bed dries, the sensor opens and allows water to move through the Gravity BluSoak tape. When the target moisture level is restored, the sensor closes automatically. Because Gravity BluSoak is porous along its entire length, it distributes water slowly across the bed instead of releasing it from individual emitter points. Frequently Asked QuestionsWhich water source should I use? Use an elevated gravity reservoir. Do not pair Gravity BluSoak with a 7.25 PSI or 15 PSI reducer; the white porous tape can be damaged by excessive pressure. What is sold separately? The water source and main supply line are sold separately. High-pressure installations also require a compatible pressure reducer. Is this the same tape as BluSoak 2.0? Yes. BluSoak 2.0 is now Gravity BluSoak. The new name clarifies which water setup to use.Gravity BluSoak Drip Tape · Compare raised bed watering kits · Build a complete irrigation system · Preset Blumat setup instructions BluSoak fitting-tightening instructions. Fitting shown with black tape; the same tightening method applies to white Gravity BluSoak. Select the image to enlarge.

Read more less

High-Pressure BluSoak Raised Bed Kits pair a preset 9" Blumat sensor with ultra-low-flow, emitter-style High-Pressure BluSoak drip tape. The 6-inch emitter spacing promotes continuous lateral wicking and uniform moisture across raised beds and large containers. Designed exclusively for pressurized installations operating between 10 and 15 PSI. These kits require a regulated hose bib or pump system and will not operate correctly from gravity pressure. Formerly described as BluSoak 3.0 high-pressure kits. The removable straight-line layout makes the system easy to lift out, amend beneath, and reinstall between cycles. Pressure & Water Source Requirements ＋ Required operating pressure: 10–15 PSI Works with a regulated hose bib, municipal supply, or pump system Use a 1-bar (15 PSI) reducer or an adjustable pressure reducer set within the operating range Not compatible with gravity-fed systems The pump, hose connection, pressure reducer, and main supply line are not included. Kit Options ＋ 2×4 Bed / Large Container — Two straight runs and 10 ft of High-Pressure BluSoak 4×4 Bed — Four straight runs and 20 ft of High-Pressure BluSoak 4×8 Bed — Four straight runs and 40 ft of High-Pressure BluSoak What's Included ＋ Preset 9" Blumat sensor High-Pressure BluSoak drip tape with 6-inch emitter spacing 8mm SuperFlex header lines Required in-bed BluSoak fittings and adapters What You'll Also Need ＋ This kit covers the irrigation components inside the bed. To complete the system, you will also need: An 8mm supply line running from the water source to the Blumat sensor A pressurized water source such as a hose bib or pump A compatible pressure reducer set between 10 and 15 PSI Straight-Line Layout ＋ Lift the irrigation assembly out before amending the bed Reinstall it without rebuilding a woven layout Keep the tape runs clean, modular, and easy to service Maintain consistent pressure distribution through header-fed straight runs How It Works ＋ The preset Blumat sensor responds continuously to soil moisture and controls water flow into the tape. As the bed dries, the sensor opens. When the target moisture level is restored, it closes automatically. High-Pressure BluSoak releases water from closely spaced emitters. At 10–15 PSI, the low flow rate and 6-inch spacing create stable, predictable moisture distribution without relying on a timer. Installation Notes ＋ Cut the tape directly through an emitter, not between emitters. Position the first emitter approximately 6 inches from the fitting. Fully tighten all tape fittings; even small leaks can reduce pressure and cause uneven performance. Purge the supply line and confirm full finished-system pressure before calibrating or adjusting the sensor. Frequently Asked QuestionsWhich water source should I use? Use a hose bib or pump regulated to 10–15 PSI. Choose a Blumat-compatible 15 PSI reducer or an adjustable reducer set within that range. A 7.25 PSI reducer does not provide enough pressure. What is sold separately? The water source and main supply line are sold separately. High-pressure installations also require a compatible pressure reducer. Is this the same tape as BluSoak 3.0? Yes. BluSoak 3.0 is now High-Pressure BluSoak. The new name clarifies which water setup to use.High-Pressure BluSoak Drip Tape · Compare raised bed watering kits · Build a complete irrigation system · Preset Blumat setup instructions High-Pressure BluSoak cutting and fitting instructions. Select the image to enlarge.

Read more less