Products

Description Replacement if you break the ceramic carrot bottom of the blumat.

Read more less

Take a vacation and let your plants look after themselves. Blumat Classic Plant Savers ensure a constant supply of water. They automatically supply just the right amount - never too much or not enough. Your plants will love it. They won't experience the drying out that stunts growth or the over-watering that squeezes the air out of the soil and keeps them from "breathing" properly. As the soil dries, the ceramic cone delivers water gradually into the surrounding earth - thereby creating a vacuum within the cone which draws water from the nearby container of water. Once the soil is moistened the Blumat will cease flowing water. It waters your plants only as needed. You can even add fertilizer to the water supply. This slow, continual feeding encourages prolific growth. Blumat Classic will only draw water up 12 inches (30cm). If the surface of the water in your container is lower than this, the flow of water will be restricted and the plants gradually dry out. Each Blumat has a limit on how fast it can deliver water. Several cones may be necessary for larger plants in order to meet the higher water needs. In this case, a larger reservoir of water must also be available. Set Up Fill a bowl with water. Remove the top of the Blumat Put both the top and ceramic cone into the bowl to soak for at least 15 minutes. Holding the cone and cap underwater, knock out the air bubbles in each piece and press the top on tightly. Push the ceramic cone completely into the soil. Extra large plants should be provided with two or three cones. Put the hose right to the bottom of a full container of water. Add a little liquid fertilizer if necessary. The level of water in the container should be level with or below the green cap. Raising or lowering the water container increases or reduces the flow rate. Maintenance Once a year, place the hose in hot water. Clean the inside of the ceramic cone with a brush and the outside with sandpaper or a pot scrubber type pad. Tips If you intend to be away from home for any length of time, ensure that the water container is large enough. Depending on type, size and season, a plant will require 1/4 to 1 litre (1 qt.) of water weekly. Delivery of water to the soil in the flower pots is automatic. If you do not refill the water container the Blumat will dry out. To restore the function, the Blumat Jr. must be refilled. (Follow steps 1-5).

Read more less

Description Extend the reach of your Blumat sensors. Sometimes, it's best to have your water source further away from your plants than the 33" that comes with Blumat. This little kit offers 10 additional feet of tubing plus 2 coupling fittings and a tee fitting. The couplings allow you to extend your watering range and the tee allows you to water two separate plants from the same water line. Components This Kit Includes: 3mm Tubing (10 ft.) (IG15473V) 2x 3mm Couplings (IG15520) 3mm Tee (IG15581)

Read more less

No power, timers, or stress—this automatic system keeps your plants watered while you're away or just too busy. Easily expandable and perfect for stress-free, "green-thumb" results. Without batteries, timers, electricity, or even a conventional water source, Blumat Classics siphon water from a reservoir into the plant containers. They give the plants water slowly through a porous ceramic cone so you won’t worry about squeezing the important air pockets out of the potting mix, under, or over-watering. Just place each cone in the potting soil, and connect to the provided main line attached to the reservoir. You can also add more Classics to the main 8mm line or add another kit and second bulkhead fitting to the same bucket to extend the number of plants. This specific kit can water up to 10 days minimum, 20 days max. Click here to read/download instructions.

Read more less

Blumat Classics with Adapters – Elegant Self-Watering, Now More Flexible Than Ever The next evolution of automatic plant care — upgraded Blumat Classics with all the trusted, plant-saving performance of the originals — now with enhanced flexibility and a cleaner, more refined setup. Keep your plants happy, hydrated, and thriving — no matter where you place them. Why you will love them: 🌱 New & Improved Design – A refined, upgraded kit for better performance and longer life ✂️ Fix It Fast – Accidentally snipped a line while rearranging your jungle? With this kit, you can repair it in seconds  🪴 Customize Your Layout  – Shorten lines for a neater, more compact look, or extend them up to an extra 3 feet for plants farther from your water source 💧 Perfectly Hydrated, Always – Your plants get exactly the moisture they need — whether you’re home, at work, or away on vacation. Blumat Classic with Adapters is the elegant evolution of the world’s favorite self-watering cone — designed for houseplant lovers who want beauty, simplicity, and a little bit of magic in their watering routine. The self-watering ease of the original Blumat Classics — now with more ways to adapt, repair, and expand your system to fit your unique space. Add a little bit of magic in your houseplant watering! Repair accidentally cut lines Shorten input lines to make more neat and compact Extend lines 3’ for plants further away from water source

Read more less

Not as elegant as our Glass Globe version and doesn't give out as much water; but, this one costs less than half as much and can really help your plants. Depending on temperature, potting mix and plant type; it typically goes about 5 days before needing to be filled up again.  These water slowly and the slower you water, the deeper the water goes, the deeper the roots go, and  the more access plants have to moisture and nutrients. The stronger and more healthy they become and the more resistant to under-watering, over-watering, and to pests. 

Read more less

The Blumat Digital moisture meter is a super accurate water moisture reader that measure the moisture content of your plant at root level. This is the replacement top for the moisture meter and is great for making an old item brand new!DO NOT WET THE DISPLAY. Moisture can cause damage to the LCD display. If using outside or in conjunction with hand-watering or foliar feeds, use our cap here.

Read more less

Description Get reliable soil moisture readings in seconds. The Blumat Digital Moisture Meter is purpose-built for potting soil, giving you consistent results you can trust. Unlike cheap probes or finger tests, it delivers accurate, repeatable readings instantly. Whether you’re managing a Blumat system or simply want healthier plants, this is the tool that takes the guesswork out of watering and helps you maintain the soil sweet spot for healthier, more resilient plants. Available Options Choose the setup that fits your needs: Meter Only – Base unit for reliable soil moisture readings. Meter + Protective Cap – Adds UV and moisture protection for outdoor use. Meter + Protective Cap + Battery – Includes a spare CR2032 3-volt battery so you’re never caught without power. Complete Kit (Meter + Cap + Battery + Coring Tool) – Full field kit with the Blumat Coring Tool (1" wide, 11"+ long) for precise sensor installation and low-impact soil work. Notes The top of the meter is not waterproof. Do not submerge or expose it to standing water. Protective cap should not be seated directly into soil, as trapped humidity can damage the sensor. Reset Instructions Click here for instructions. Video

Read more less

Description These are great for watering long plant beds, planter boxes, and giving large plants an even amount of water in a circle around them. They connect to a Tropf-Blumat or a Maxi.This is less expensive than adding more sensors but you may need to add a filter to your system if you use nutrients in your water so they don't clog.  Two barbs let you connect tubing on both sides of the dripper for up to five drip locations from one Tropf-Blumat (dripper chain). The end-distributor dripper has a drip nozzle on one side only for use as the end piece in a dripper chain. You can go as far as 100 cm (39") from the sensor with these and they water about 20 cm wide (8"). Minimum pressure to use them like this is 4.5 psi. You can go down as low as 2 psi but the last dripper or two might not put out much water. By adjusting the black screw on the top, you can use more. In pressure systems, customers report successfully using as many as 25 with just one Blumat sensor.  

Read more less

Description Each Tropf Blumat can control 5 of these distribution drippers and saturate a 40" length - either in a row or around a large plant. So with this set you can set up 10 mini systems like that. The caps go on the ends of the last distribution dripper to stop the water flow. If your plants and conditions are the same, you can also put one Tropf Blumat in the first pot with one distribution dripper and one or two in each put after that.

Read more less

Description Each Tropf Blumat can control 5 of these distribution drippers and saturate a 40" length - either in a row or around a large plant. In a pressure system, by adjusting the black screw, it's possible to do more than 5 but with a gravity system, usually better to stay with 2-3. If your plants and conditions are the same, you can also put one Tropf Blumat in the first pot with one distribution dripper and one or two in each plant after that. One customer reported doing this successfully with 25 distribution drippers running off just one Blumat sensor.

Read more less

Description Use these to end a Blumat distribution line. The regular distribution drippers have barbs on both sides so you need a way to end them without water dripping out too fast. You can do that with an end cap (IG15509) or with one of these. They are less expensive than the standard drippers and much easier to take on and off than the end caps. The end caps often need pliers to remove but they just pull on and off.

Read more less

Description These are great for watering long plant beds, planter boxes, and giving large plants an even amount of water in a circle around them. They connect to a Tropf-Blumat or a Maxi.This is less expensive than adding more sensors but you may need to add a filter to your system if you use nutrients in your water so they don't clog. This pack contains 10 distributors and 2 meters of (6.5 feet) of 3mm drip tubing. Two barbs let you connect tubing on both sides of the dripper for up to five drip locations from one Tropf-Blumat (dripper chain). The end-distributor dripper has a drip nozzle on one side only for use as the end piece in a dripper chain. You can go as far as 100 cm (39") from the sensor with these and they water about 20 cm wide (8"). Minimum pressure to use them like this is 4.5 psi. You can go down as low as 2 psi but the last dripper or two might not put out much water. By adjusting the black screw on the top, you can use more. In pressure systems, customers report successfully using as many as 25 with just one Blumat sensor. Components Set Includes: 10 Distribution Drippers (8 Regular + 2 End Drippers) (IG15557,IG15558) 2 Meters (6.5 ft) 3mm Drip Tube (IG16021V)    

Read more less

Description These are great for watering long plant beds, planter boxes, and giving large plants an even amount of water in a circle around them. They connect to a Tropf-Blumat or a Maxi.This is less expensive than adding more sensors but you may need to add a filter to your system if you use nutrients in your water so they don't clog. This comes with 4 packs. Each pack contains 10 distributors and 2 meters of (6.5 feet) of 3mm drip tubing. Two nozzles allow you to connect tubing on both sides of the dripper for up to five drip locations from one Tropf-Blumat (dripper chain). The end-distributor dripper has a drip nozzle on one side only for use as the end piece in a dripper chain. You can go as far as 100 cm (39") from the sensor with these and they water about 20 cm wide (8"). Minimum pressure to use them like this is 4.5 psi. You can go down as low as 2 psi but the last dripper or two might not put out much water. By adjusting the black screw on the top, you can use more. In pressure systems, customers report successfully using as many as 25 with just one Blumat sensor.

Read more less

Description Pack of 10 Drip Rings 5" Revolutionize your irrigation system with our Blumat Drip Ring - the professional choice for efficient, assembly-free watering. This innovative dripper seamlessly integrates with Blumat sensors, eliminating the need for extra adapters or connectors. Key Features Blumat Sensor Compatibility: Our Drip Ring has a 3mm inlet barb that connects easily with Blumat sensors. No Assembly Required: Our plug and play design saves you valuable time and reduces labor. With this ready-to-use solution, you can enjoy the benefits of efficient irrigation without the complexities of component assembly. Nutrient Compatibility: Our Drip Ring has a built-in filter and clog resistant emitters which allow you to easily feed a variety of nutrients through the ring without fear of clogging. Durable Construction: The drip ring is made from the best quality virgin resin ensuring a highly durable product with a long lifespan. Even Distribution: With 4 strategically placed drip points, this ring delivers water precisely where your plants need it most. Invest in your plants' health and growth with the Blumat Drip Ring - the ultimate blend of convenience and professionalism for your gardening needs.

Read more less

Much better than the wine bottle versions because Blumats are so much easier to refill: just cut the bottom off plastic bottle and fill with your regular watering can. (No reason to go back and forth from your sink so many times.) Better than the globe spikes because these disperse the water evenly, not just through a hole in the bottom. Just fit this adapter into almost any standard plastic bottle, fill the bottle with water and push into the soil near a plant. The porous cone will slowly start to distribute water throughout the day. The regular size does about 200 milliliters (.43 pints) during a 24-hour period. The XL, larger size does about 300 milliliters (.63 pints). Guide to Bottle Adapter & Glass Globes

Read more less

Much better than the wine bottle versions because Blumats are so much easier to refill: just cut the bottom off plastic bottle and fill with your regular watering can. (No reason to go back and forth from your sink so many times.) Better than the globe spikes because these disperse the water evenly, not just through a hole in the bottom. Just fit this adapter into almost any standard plastic bottle, fill the bottle with water and push into the soil near a plant. The porous cone will slowly start to distribute water throughout the day. The regular size does about 200 milliliters (.43 pints) during a 24-hour period. The XL, larger size does about 300 milliliters (.63 pints). Guide to Bottle Adapter & Glass Globes

Read more less

Much better than the wine bottle versions because Blumats are so much easier to refill: just cut the bottom off plastic bottle and fill with your regular watering can. (No reason to go back and forth from your sink so many times.) Better than the globe spikes because these disperse the water evenly, not just through a hole in the bottom. Just fit this adapter into almost any standard plastic bottle, fill the bottle with water and push into the soil near a plant. The porous cone will slowly start to distribute water throughout the day. The regular size does about 200 milliliters (0.43 pints) during a 24-hour period. The XL, larger size does about 300 milliliters (0.63 pints). Guide to Bottle Adapter & Glass Globes

Read more less

Much better than the wine bottle versions because Blumats are so much easier to refill: just cut the bottom off plastic bottle and fill with your regular watering can. (No reason to go back and forth from your sink so many times.) Better than the globe spikes because these disperse the water evenly, not just through a hole in the bottom. Just fit this adapter into almost any standard plastic bottle, fill the bottle with water and push into the soil near a plant. The porous cone will slowly start to distribute water throughout the day. The regular size does about 200 milliliters (.43 pints) during a 24-hour period. The XL, larger size does about 300 milliliters (.63 pints). Guide to Bottle Adapter & Glass Globes

Read more less

This kit includes the Blumat Medium Box Kit which are designed to water areas up to 3.5 square meters, or 12 potted plants. Blumat systems can adjust to any plant type or desired moisture level. This specific kit comes with 5" carrots, which are better for smaller potted plants (10 gallons at most). If you have large plants (10+ gallon pots), we recommend using 9" carrots, or Maxis, to get water deep into the soil. The reservoir comes with one bulkhead fitting. *If you are looking for a closed loop system please take a look at our medium deluxe kit. Increase your yields and decrease grow times. Our fully-automatic, self-watering systems save time, water, and nutrients - and still ensure healthier, more potent, and faster-growing crops. Perfect for landscapers and home gardeners. It is easily installed with a pair of scissors and connects directly to your reservoir. This kit includes twelve, 5" carrots and all the parts required for a gravity-fed system. Reservoirs should be at least 3' above ground-level. An optional Pressure Reducer attached to garden hose or faucet can provide enough water for up to 500 Blumat Carrots (Search 'pressure reducer'). The Tropf Blumat system is great for watering balcony boxes, planters, hanging baskets, and row crops. It fulfills the needs of the plants on an individual basis, regardless of their location, light levels, or plant type. Our systems save your plants from excessive and improper watering. Tropf Blumat system are ideal for plant groupings that require consistent moisture, such as vegetable gardens, bushes, flower beds, grow bags and greenhouse containers. Not only do your plants receive the right amount of water, slow and consistent dripping ensures that your plants receive warmed water, avoiding shock. This Deck and Planter Kit is a great way to start your customized irrigation system. The flexible system can be expanded to include up to 500 drippers. See 'Blumat Accessories' to expand our systems to your specific needs. How it works The Tropf Blumat self-watering system functions automatically. As the soil dries, a vacuum and hydro-static pressure, coupled with a spring-loaded gating mechanism, pulls water from the main line. When the soil is sufficiently moist, pressures equalize, and the Tropf Blumat automatically stops taking in water. Each Blumat Outdoor Sensor in the Deck and Planter Set covers an area 12 inches in diameter. To expand and customize your own system, add additional Supply Hoses,Outdoor Sensors, and Distributor Drippers. PLEASE NOTE: This Tropf Blumat systems do not include a Pressure Reducer. You will need this if you are connecting your system to a threaded spigot, such as your hose/home water supply or the spigot on a rain barrel or reservoir. The Pressure Reducer is in 'Related Products' below. Let us know if we can help you select the right products for your custom irrigation system! Components This Kit Includes: 12 Blumat Carrots (5") (IG17188) 7 Meters (23 feet) of 8mm Tubing (IG15634) 1 Tee Splitter (IG17310) 1 Elbow Splitter (IG15595) 1 Hose Coupler (IG15638) 1 Hose End-Piece (IG15986) 1 Rain Barrel/Gravity Tank Connectors and Installation Instructions (IG15691) 1 5 Gallon Reservoir (IG15600) 1 Bulkhead Fitting (IG15494)

Read more less

Description These really help in greenhouses and raised beds. They help you neatly go around corners in your Tropf Blumat irrigation system. The right-angled elbow eliminates bends in the tubing that can limit the flow in your irrigation system. The black plastic is robust and barbed at both ends to hold the tube securely in place. Contains three 8mm (5/16") elbows.

Read more less

Use this special end piece to end your 8mm line and enter 3mm tubing. Use the special 3mm cap to cover and plug the 3mm elbow. This can be used to end your 8mm supply line, and then take out the little end black cap if you want to add another sensor or simply want to bleed water out.

Read more less

In case you break a glass globe, you can still keep using the bottle adapter base alone or get this replacement top. The same adapter will work in the same way.

Read more less

Not just a beautiful decoration, these glass watering globes include the patented Blumat Bottle Adapters and regulate water flow by soil type and dryness. The perfect solution for taking care of your houseplants, they slowly and steadily provide water without either over or under-watering. A big help both while away on vacation as well as when still at home, they not only give the plants water but also regulate it based on temperature, growth cycles, and size of plant.An automatic plant watering device that requires no power, electricity, batteries, timers, or any other accessories, they can dramatically upgrade your watering schedule. Details Materials Glass Plastic Silicone Clay Dimensions Weight: 18 oz. Total height: 8 & 1/2" Diameter: 4 & 3/8" Volume: 23 fl. oz. Flow Rate Approx. 7 fl. oz. per 24 hours Instructions Fill the glass globe with water. Push the cone downward into the soil. Watch your plant thrive! Comparison Chart Tropf Blumat Blumat Classic Glass Globe Blumat Bottle Adapter Vacation Ready ✓ ✓ ✓ ✓ Adjustable ✓ ✓ Out-of-Box Ready ✓ ✓ ✓ Custom System Integration ✓ Max. Water Delivery p/ 24 hrs Adjustable/Unlimited 200ml 118ml 200ml Ideal Location to Water Raised Bed/Garden/Potted Plants Houseplant Houseplant Houseplant Additional Info More Info Refill the Glass Globe with water as often as needed to keep plants constantly watered. The Glass Globe is an aesthetically-superior option to plastic or wine bottles. This 23 oz (4 3/8") glass globe can deliver about 200 milliliters (.43 pint) during a 24 hour period.   Video

Read more less