Products

Description Tape End Closure Flat

Read more less

Description Tape End Closure Flat

Read more less

Description Tees for 1/4" line.

Read more less

Description Tees for 1/4" line.

Read more less

Description Transfer Barbs 1/4"

Read more less

Description Transfer Barbs 1/4"

Read more less

Description Sink your water deep where it won't evaporate and will get where your big roots need it most. Have you ever scratched the ground surface after a big rain or watering expecting lots of wet earth only to find only surface moisture? That's where most drip irrigation gets the water. This is fine for small plants but what about your big trees and shrubs? These 7" soaker stakes will solve the problem. Just install inline with standard 1/2" drip tubing and watch how much faster your large plants grow. The elbows are for single site application or to end a series of stakes. 

Read more less

Get out of Trim Jail early with good behavior, and the right tools! Happy Hydro has put together a bundle of our favorite indoor gardening accessories. See your herbs with clarity, trim them with precision, and dry them to perfection with this accessory kit. Kief CollectorExactly that! Collect all of your kief/pollen from your harvest. It certainly beats finding leaves in your couch or all over your floor covered in your dogs fur. A perfect size tabletop or laptop work station that will collect all of your small leaves and the micron screen will allow the fallen trichomes to fall through. When you're done, you'll have a separate pile of sugar leaves and when you lift up the second tray you'll have a sizeable amount of kief/pollen! Versatile 6-Tier Herb Drying RackThe Happy Hydro mesh drying net makes it easy to dry buds slowly and evenly. The round design allows for 360-degree access. With 6 inches of spacing between tiers, it's incredibly easy to inspect and manicure drying plant matter. When drying is complete, simply shake out the mesh drying rack, allow it to collapse, and store it away in its convenient storage bag until next harvest. Wire frames make our herb drying rack rigid, sturdy, and simple to use. Best of all: there is no assembly required!Jeweler's Lighted High-Power Eye Loupe 30 & 60x LEDSee microscopic detail with complete clarity. Our professional-grade Jewelry Loupe with LED illumination is an indispensable tool for indoor gardeners. Equipped with dual lenses, this compact folding magnifier fits discreetly in a pocket. Each lens features a bright LED light, so you can evaluate even the tiniest details. Includes batteries and carrying case.Ergonomic Spring-Loaded Trimming Scissors with Stainless-Steel BladesTake the pain out of gardening! If you’ve been using regular scissors to trim, shape, or prune, then it’s time to say goodbye to aching wrists, sore hands, and blisters! Now you can accomplish the task effortlessly with Happy Hydro’s premium stainless-steel scissors. The razor-sharp blades come to an ultra-fine point for the most delicate pruning tasks. Components Harvest Bundle includes: Kief Collector (IG19195) 6 Tier Hanging Drying Rack - Collapsible - Includes Carrying Bag (IG19195) LED Loupe with 30x and 60x Magnifying Lenses - Includes Batteries and Case 2x Trimming Scissors | Stainless-Steel | 1x Curved Blade, 1x Straight Blade

Read more less

Description A game-changing innovation: pre-calibrated 5" and 9" Blumat Tropfs These two new products eliminate almost all the problems people have setting up and maintaining Tropf Blumats, save a huge amount of time, and also make it easy to adjust your entire system all at once! Most of the time people spend setting up a Blumat system involves adjusting the sensors - both initially and when you need to make a change. We can do that for you now so all you'll have to do is plug them in. To make small adjustments later to provide more or less water, you can make a 10-second adjustment on an adjustable pressure reducer (if you have one) and change the flow rates for all at once. Both 5" and 9" sensors arrive pre-calibrated with two markings on the brown adjustment dial - one for gravity and one for pressure systems. This new innovation makes the Blumat Tropf practical for large commercial systems with thousands of plants as well as preventing the most common problems people have while dramatically decreasing setup time for small systems. Pre-calibrated for most soil/media types like living soil, standard potting mixes, coco, and peat; they take most of the work and worry out of the installation! Set just where you want them to be right out of the box. We normally recommend the 9" Maxis in these systems but also make this 5" size for pots smaller than 5 gallons. This listing includes one 5 inch preset Blumat Tropf with a protective cap to prevent the setting from being accidentally changed. They come with two markings on the brown adjustment dial. Use the red mark for gravity systems and the blue one if you have pressure. Click here to read/download instructions.

Read more less

Description The Tropf-Blumat (Tropf means drip in German) is a sensor that automatically supplies plants water through its thin tubing. This ceramic cone employs the principle of hydrostatic pressure, that delivers water extremely slowly, and at the plant’s own preferred rate. Allowing each plant to determine its own irrigation schedule. Blumat Sensors can be used as standalone devices or can also be integrated with drip emitters (we call them “distribution drippers”), drip tape (BluSoak), or capillary mats. These three components assist Blumat sensors in going further. While a Blumat typically irrigates a very small area (a 1-gallon container for example), a single Blumat can irrigate entire garden beds when attached to the Blusoak. How It Works Each Tropf Blumat is filled with water and voided of air prior to being connected to a pressurized line (pressure from gravity-feed is adequate). The water inside the Blumat is in a completely sealed environment. The only exposure it has is through the pores in the ceramic cone. As soil surrounding the cone dries It pulls on the moisture inside the cone through osmotic pressure. Since this is a sealed environment and the pressure cannot equalize, this pulls on a plastic diaphragm in the top of the Blumat. When the diaphragm is pulled down, it allows an irrigation tube running through the top of the valve of the Blumat to open and emit moisture. It does this very gradually. As the water is emitted through the Blumat, the moisture is gradually restored to the soil surrounding the porous ceramic. This relieves the pressure difference between the chamber inside the Blumat and the surrounding soil. This stops pulling on the diaphragm, and the diaphragm restores its former position of pinching the irrigation tubing shut. Allowing each plant to determine its own watering schedule. *The brown knob on top of each Tropf Blumat can be individually calibrated to specific plant species, strain/cultivar/varietal, or media. Details Materials Clay Silicone Plastic Dimensions Weight: 1.3oz Total length: 5.2" Max soil depth: 4" Cap width: 1.4" Sensor width: 1" Tubing length: 8" Connectors Fits 8mm Blumat and Superflex tubing. Flow Rate Adjustable Stand Alone Product? No. Requires water source. Instructions Tropf Blumat Instructions Water your garden thoroughly (ideally overnight) before installation. Prep the Carrots: Fill a container with cooled, non-aerated water (if you’re not sure, boil & cool the water first). Separate the ceramic bottoms from the plastic tops, and soak both parts for at least 15 minutes. While holding the green top underwater use a pipette/eyedropper or your thumb to squirt water into the holes in the green cap. You want to displace any small air bubbles stuck in the cap. Hold both cap and ceramic bottom underwater. Confirm the ceramic bottom and cap are both completely void of air, and reassemble the Blumat ceramic bottom with the green cap while both components are still underwater. Soak the assembled Blumat sensors and keep them submerged for a minimum of 15 minutes. Blumat sensors can stay in water indefinitely, but avoid algae growth and light exposure. While the Tropf Blumats are soaking: Connect the 8mm tubing to a reservoir or Blumat Pressure Reducer which has been integrated to a pressurized line. Run the 8mm tubing to your plants. Installation: Water the garden again, and push the Blumat Carrot in where you would like the moisture sensed, ensuring the ceramic cone is completely covered and firmly anchored. Cut the 8mm tubing and insert the 8 x 8 x 3mm tee (included with each Blumat). Slide the 8mm tubing over the 8mm barbs on the tee. For the last carrot, use the elbow insert instead of the tee. Alternatively, keep the tee in place. Use a small amount of 8mm tubing to attach a 8mm shut-off valve following your final Blumat carrot. This will function as an air/debris purge valve. Adjustment: Turn on the water supply and adjust the flow to each Blumat. Open the valve on the Blumat until flow is visible. Keeping the 3mm tubing level with the valve of the Blumat, slowly tighten (turn clockwise) the Blumat until a hanging drop is just achieved. The flow should just be stopped, but do not twist beyond that point for the “hanging drop.” Tighten the valve on the Blumat an additional two triangles. This will roughly calibrate the sensor to keep maintain current moisture levels.* *If using BluSoak drip tape, do not follow this step. Keeping your sensors at the hanging drip is ideal. Monitor: Come back in 12-24 hours, and make adjustments to each Blumat. If a container or area is over-watered, tighten the Blumat valve (turn clockwise). If a container or area is under-watered, open the Blumat valve (turn counter-clockwise). Repeat the previous step until your system is exactly where you’d like it. The Blumat Digital Moisture Meter is a great tool for assisting with this step. Comparison Chart Tropf Blumat Blumat Classic Glass Globe Blumat Bottle Adapter Vacation Ready ✓ ✓ ✓ ✓ Adjustable ✓ ✓ Out-of-Box Ready ✓ ✓ ✓ Custom System Integration ✓ Max. Water Delivery p/ 24 hrs Adjustable/Unlimited 200ml 118ml 200ml Ideal Location to Water Raised Bed/Garden/Potted Plants Houseplant Houseplant Houseplant Additional Info Maintenance Guide to Tropf Blumat Sensors | Irrigation Equipment Blumat Troubleshooting & Operating Tips/Tricks | Irrigation Equipment Video

Read more less

Description The Tropf-Blumat (Tropf means drip in German) is a sensor that automatically supplies plants water through its thin tubing. This ceramic cone employs the principle of hydrostatic pressure, that delivers water extremely slowly, and at the plant’s own preferred rate. Allowing each plant to determine its own irrigation schedule. Blumat Sensors can be used as standalone devices or can also be integrated with drip emitters (we call them “distribution drippers”), drip tape (BluSoak), or capillary mats. These three components assist Blumat sensors in going further. While a Blumat typically irrigates a very small area (a 1-gallon container for example), a single Blumat can irrigate entire garden beds when attached to the Blusoak. How It Works Each Tropf Blumat is filled with water and voided of air prior to being connected to a pressurized line (pressure from gravity-feed is adequate). The water inside the Blumat is in a completely sealed environment. The only exposure it has is through the pores in the ceramic cone. As soil surrounding the cone dries It pulls on the moisture inside the cone through osmotic pressure. Since this is a sealed environment and the pressure cannot equalize, this pulls on a plastic diaphragm in the top of the Blumat. When the diaphragm is pulled down, it allows an irrigation tube running through the top of the valve of the Blumat to open and emit moisture. It does this very gradually. As the water is emitted through the Blumat, the moisture is gradually restored to the soil surrounding the porous ceramic. This relieves the pressure difference between the chamber inside the Blumat and the surrounding soil. This stops pulling on the diaphragm, and the diaphragm restores its former position of pinching the irrigation tubing shut. Allowing each plant to determine its own watering schedule. *The brown knob on top of each Tropf Blumat can be individually calibrated to specific plant species, strain/cultivar/varietal, or media. Details Materials Clay Silicone Plastic Dimensions Weight: 1.3oz Total length: 5.2" Max soil depth: 4" Cap width: 1.4" Sensor width: 1" Tubing length: 8" Connectors Fits 8mm Blumat and Superflex tubing. Flow Rate Adjustable Stand Alone Product? No. Requires water source. Instructions Tropf Blumat Instructions Water your garden thoroughly (ideally overnight) before installation. Prep the Carrots: Fill a container with cooled, non-aerated water (if you’re not sure, boil & cool the water first). Separate the ceramic bottoms from the plastic tops, and soak both parts for at least 15 minutes. While holding the green top underwater use a pipette/eyedropper or your thumb to squirt water into the holes in the green cap. You want to displace any small air bubbles stuck in the cap. Hold both cap and ceramic bottom underwater. Confirm the ceramic bottom and cap are both completely void of air, and reassemble the Blumat ceramic bottom with the green cap while both components are still underwater. Soak the assembled Blumat sensors and keep them submerged for a minimum of 15 minutes. Blumat sensors can stay in water indefinitely, but avoid algae growth and light exposure. While the Tropf Blumats are soaking: Connect the 8mm tubing to a reservoir or Blumat Pressure Reducer which has been integrated to a pressurized line. Run the 8mm tubing to your plants. Installation: Water the garden again, and push the Blumat Carrot in where you would like the moisture sensed, ensuring the ceramic cone is completely covered and firmly anchored. Cut the 8mm tubing and insert the 8 x 8 x 3mm tee (included with each Blumat). Slide the 8mm tubing over the 8mm barbs on the tee. For the last carrot, use the elbow insert instead of the tee. Alternatively, keep the tee in place. Use a small amount of 8mm tubing to attach a 8mm shut-off valve following your final Blumat carrot. This will function as an air/debris purge valve. Adjustment: Turn on the water supply and adjust the flow to each Blumat. Open the valve on the Blumat until flow is visible. Keeping the 3mm tubing level with the valve of the Blumat, slowly tighten (turn clockwise) the Blumat until a hanging drop is just achieved. The flow should just be stopped, but do not twist beyond that point for the “hanging drop.” Tighten the valve on the Blumat an additional two triangles. This will roughly calibrate the sensor to keep maintain current moisture levels.* *If using BluSoak drip tape, do not follow this step. Keeping your sensors at the hanging drip is ideal. Monitor: Come back in 12-24 hours, and make adjustments to each Blumat. If a container or area is over-watered, tighten the Blumat valve (turn clockwise). If a container or area is under-watered, open the Blumat valve (turn counter-clockwise). Repeat the previous step until your system is exactly where you’d like it. The Blumat Digital Moisture Meter is a great tool for assisting with this step. Comparison Chart Tropf Blumat Blumat Classic Glass Globe Blumat Bottle Adapter Vacation Ready ✓ ✓ ✓ ✓ Adjustable ✓ ✓ Out-of-Box Ready ✓ ✓ ✓ Custom System Integration ✓ Max. Water Delivery p/ 24 hrs Adjustable/Unlimited 200ml 118ml 200ml Ideal Location to Water Raised Bed/Garden/Potted Plants Houseplant Houseplant Houseplant Additional Info Maintenance Guide to Tropf Blumat Sensors | Irrigation Equipment Blumat Troubleshooting & Operating Tips/Tricks | Irrigation Equipment Video

Read more less

Description The Tropf-Blumat (Tropf means drip in German) is a sensor that automatically supplies plants water through its thin tubing. This ceramic cone employs the principle of hydrostatic pressure, that delivers water extremely slowly, and at the plant’s own preferred rate. Allowing each plant to determine its own irrigation schedule. Blumat Sensors can be used as standalone devices or can also be integrated with drip emitters (we call them “distribution drippers”), drip tape (BluSoak), or capillary mats. These three components assist Blumat sensors in going further. While a Blumat typically irrigates a very small area (a 1-gallon container for example), a single Blumat can irrigate entire garden beds when attached to the Blusoak. How It Works Each Tropf Blumat is filled with water and voided of air prior to being connected to a pressurized line (pressure from gravity-feed is adequate). The water inside the Blumat is in a completely sealed environment. The only exposure it has is through the pores in the ceramic cone.   As soil surrounding the cone dries It pulls on the moisture inside the cone through osmotic pressure. Since this is a sealed environment and the pressure cannot equalize, this pulls on a plastic diaphragm in the top of the Blumat. When the diaphragm is pulled down, it allows an irrigation tube running through the top of the valve of the Blumat to open and emit moisture. It does this very gradually. As the water is emitted through the Blumat, the moisture is gradually restored to the soil surrounding the porous ceramic. This relieves the pressure difference between the chamber inside the Blumat and the surrounding soil. This stops pulling on the diaphragm, and the diaphragm restores its former position of pinching the irrigation tubing shut. Allowing each plant to determine its own watering schedule.   *The brown knob on top of each Tropf Blumat can be individually calibrated to specific plant species, strain/cultivar/varietal, or media. Details Materials Clay Silicone Plastic   Dimensions Weight: 1.3oz Total length: 5.2" Max soil depth: 4" Cap width: 1.4" Sensor width: 1" Tubing length: 8"   Connectors Fits 8mm Blumat and Superflex tubing.   Flow Rate Adjustable   Stand Alone Product? No. Requires water source.   Instructions Tropf Blumat Instructions Water your garden thoroughly (ideally overnight) before installation. Prep the Carrots: Fill a container with cooled, non-aerated water (if you’re not sure, boil & cool the water first). Separate the ceramic bottoms from the plastic tops, and soak both parts for at least 15 minutes. While holding the green top underwater use a pipette/eyedropper or your thumb to squirt water into the holes in the green cap. You want to displace any small air bubbles stuck in the cap. Hold both cap and ceramic bottom underwater. Confirm the ceramic bottom and cap are both completely void of air, and reassemble the Blumat ceramic bottom with the green cap while both components are still underwater. Soak the assembled Blumat sensors and keep them submerged for a minimum of 15 minutes. Blumat sensors can stay in water indefinitely, but avoid algae growth and light exposure. While the Tropf Blumats are soaking: Connect the 8mm tubing to a reservoir or Blumat Pressure Reducer which has been integrated to a pressurized line. Run the 8mm tubing to your plants. Installation: Water the garden again, and push the Blumat Carrot in where you would like the moisture sensed, ensuring the ceramic cone is completely covered and firmly anchored. Cut the 8mm tubing and insert the 8 x 8 x 3mm tee (included with each Blumat). Slide the 8mm tubing over the 8mm barbs on the tee. For the last carrot, use the elbow insert instead of the tee. Alternatively, keep the tee in place. Use a small amount of 8mm tubing to attach a 8mm shut-off valve following your final Blumat carrot. This will function as an air/debris purge valve. Adjustment: Turn on the water supply and adjust the flow to each Blumat. Open the valve on the Blumat until flow is visible. Keeping the 3mm tubing level with the valve of the Blumat, slowly tighten (turn clockwise) the Blumat until a hanging drop is just achieved. The flow should just be stopped, but do not twist beyond that point for the “hanging drop.” Tighten the valve on the Blumat an additional two triangles. This will roughly calibrate the sensor to keep maintain current moisture levels.* *If using BluSoak drip tape, do not follow this step. Keeping your sensors at the hanging drip is ideal. Monitor: Come back in 12-24 hours, and make adjustments to each Blumat. If a container or area is over-watered, tighten the Blumat valve (turn clockwise). If a container or area is under-watered, open the Blumat valve (turn counter-clockwise). Repeat the previous step until your system is exactly where you’d like it. The Blumat Digital Moisture Meter is a great tool for assisting with this step. Comparison Chart Tropf Blumat Blumat Classic Glass Globe Blumat Bottle Adapter Vacation Ready ✓ ✓ ✓ ✓ Adjustable ✓ ✓ Out-of-Box Ready ✓ ✓ ✓ Custom System Integration ✓ Max. Water Delivery p/ 24 hrs Adjustable/Unlimited 200ml 118ml 200ml Ideal Location to Water Raised Bed/Garden/Potted Plants Houseplant Houseplant Houseplant Additional Info Maintenance Guide to Tropf Blumat Sensors | Irrigation Equipment Blumat Troubleshooting & Operating Tips/Tricks | Irrigation Equipment     Video

Read more less

Description The Tropf-Blumat Maxi acts as a regulator and dripper, just like the standard 5” Tropf-Blumat. This one is 9 inches long though. You put it in the ground 6 - 7.5 inches so it senses the moisture at a deeper level. This is important when your plants get bigger because the regular Blumat sensor might turn the water off too soon. This one might turn it off too soon if your plant still has surface roots. Some growers use both - especially if they are growing in coco or a hydroponic system. The Tropf-Blumat (Drip-Blumat) is a sensor that supplies plants with drips of water via thin tubing. As the soil dries, its natural suction power triggers the opening of the Tropf Blumat allowing the water to flow. When the soil is sufficiently moist, the Tropf Blumat automatically stops. The system functions fully automatically. Every plant, every container or group of plants requires at least 1 Tropf-Blumat adjusted to the individual needs of the plant. Larger containers or surfaces require longer or more than one sensor. All Tropf-Blumats are connected using one supply tube, this allows for flexibility in the layout and is changeable at any time. Automatically waters individual plants and only when needed. There are a few options for a water source; you can either connect the system directly to your hose tap or rain barrel (with fittings not supplied with this product).

Read more less

Description These let you split off branch feeder tubes and terminate them instead of making wide loops with your feeder tube. Outside for big plants you may not need to use these but for smaller areas and greenhouses, they really help. Contains 2 tees and 2 end-pieces.

Read more less

Description Irrometer sensors come made for soil (outside, gardens and farms) and for planting and potting mixes (indoor, greenhouses, and outside beds). This one - best for using with potting mixes - includes two sensors and the parts needed to set it up: a hand vacuum pump, a bottle of Irrometer fluid, 25 monthly chart forms, and a reference book. After setting up the sensors, you can use the pump to remove air from them to ensure maximum sensitivity and accuracy.

Read more less

Description Irrometer sensors come made for soil (outside, gardens and farms) and for planting and potting mixes (indoor, greenhouses, and outside beds). This one - best for using with potting mixes - includes two sensors and the parts needed to set it up: a hand vacuum pump, a bottle of Irrometer fluid, 25 monthly chart forms, and a reference book. After setting up the sensors, you can use the pump to remove air from them to ensure maximum sensitivity and accuracy.

Read more less

Description These universal stakes solve the issue of having to find the perfect hold down stakes to fit your tubing. Make your lawn and irrigation system's more beautiful by having your tubing be well organized, held in place, and more appealing. These stakes come in any quantity selected, and are ideal for 3mm, 8mm, 1/8', 1/4', and most distribution lines. Purchase by bulk, by the "each"

Read more less

Description Information you can use, when you need itMeasure the soil moisture available for your plants and automatically transmit to an IrroCloud Monitor. This tensiometer measures moisture levels in centibars and gives you the same information as typical analog versions you have to see in person. You can hook up to 6 of these to every IrroCloud Monitor and see the data on your smart phone, desk computer, or laptop anywhere in the world. The user-friendly IrroCloud software lets you see the  data in many ways—graphs, averages, individual sites, rain events, and several other useful configurations, turning the data into actionable information.

Read more less

Description Fast shallow-soil information when you need itLike the 12" version, this 6" sensor measures soil moisture and  transmits it to an IrroCloud Monitor. Because this one is closer to the soil surface, it works best for plants with shallow roots and for large plants when they're still small. Hook up 1-6 of these for every IrroCloud Monitor you have or plan to get and automatically have all this critical information on your phone or computer. You can also install a combination of 6" and 12" sensors on the same system with the same simple software, accuracy, graphs, averages, and  configurations.

Read more less

Description One of the main troubles people have with Gravity Blumat systems comes from forgetting to refill the reservoir and letting the carrots dry out. With this simple water level indicator installed, you can see with a quick glance how soon you'll need to refill. If you already have a 5-gallon bucket system, you can just add on the water level kit with this product. Components This Kit includes: 1' 8mm Clear Flex Tube (IG18177) 1 Blumat 8mm Tee (IG15581) 1 8mm Union (IG15638) Two Zip-Ties Bucket NOT included

Read more less

Description By far, the main trouble people have with gravity Blumat systems comes from forgetting to refill the reservoir and letting the carrots dry out. With this simple water level indicator installed, you can see with a quick glance how soon you'll need to refill. If you already have a 50 or 55-gallon drum, you can just add on the water level kit. Components This product includes: 3' 8mm Clear Flex Tube (IG18177) 1 Blumat 8mm Bulkhead (IG15691) 1 Blumat 8mm Tee (IG15581) 1 8mm Union (IG15638)

Read more less

Description 0-100 PSI READING • This liquid-filled pressure gauge and psi gauge gives accurate readings in the range of 0-100 psi! WATER PRESSURE TEST GAUGE • This gauge can be used to test water pressure, whether in your home, irrigation system, or anywhere else! SCHRADER VALVE COMPATIBLE • This gauge reads from Schrader valves, the same valves used with tire pressure gauge(s), tire gauge(s), and air pressure gauge(s)!* (This product does require an additional quick-connect fitting to read directly from Schrader Valves) RELIABLE • Unlike digital tire pressure gauge(s), this does not feature any electronic or digital components and is built to last! VERSATILE • Can be used as an air gauge, water gauge, water pressure tester, RO pressure gauge, or pool pressure gauge! Instead of having to buy, install, and maintain multiple pressure gauges; use these quick connects to just keep one and quickly test your pressure in many different places. These really help in large filtration systems where you can check before and after the filters to let you know if they need to be cleaned yet or not. The kit includes an oil-filled (so you can use at different angles) 0-100 psi gauge and you can also order the quick connects separately. Liquid-filled pressure gauge. Reads from 0-100 psi. This is ideal for pressure in irrigation tubing=lines using Shrader valves. This product can also be used to detect whether filtration systems require cleaning or not.

Read more less

Description Blumat-ready - This 5 gallon water tank comes ready with bulkheads/spigots for 8mm Blumat tubing! High quality - These buckets are made of HDPE food-grade plastic, and are assembled in the USA! Black/opaque - Designed to keep light out, these water reservoir tank(s) discourage algae growth! Ideal horticulture application - Will work for hydroponic bucket(s) or other gardening uses! Bucket with spigot(s) - Pre-installed, no tools required to get this reservoir working for your plants! Bulkheads are installed with nipples facing inward for shipping only. The bulkheads/spigots should be flipped around so that the nipples face outward for garden, horticultural, and hydroponic applications. These will work as reservoirs for Blumat watering systems, can work in hydroponic bucket system(s), can replace hydroponic reservoir(s), and are essentially kits for water barrels with spigots! You certainly don't need to be DIY-friendly to use these buckets, as we do the work requiring elbow grease and tools to get the bulkheads installed. These will deliver water wherever you take your tubing! The bulkheads perfectly integrate to 8mm tubing. We would highly recommend our ultra-high quality and durable silicone super-flex tubing. This can be installed onto this bucket - no tools required! It just slips over the nipples/barbs on the bulkheads that are pre-installed in the container. This 8mm tubing is the ideal size for Blumats, and will slip right over the barbs on the 8mm x 3mm x 8mm Tees (included with each Tropf Blumat). This bucket is really like hitting the "easy button" for Blumat systems, hydroponic watering systems, backyard gardening applications, or just about any other application that you require a 5-gallon reservoir for. This is really like a water barrel spigot kit that has already been configured and assembled for you! 5 Gallon Reservoir with two thru-hulls and lid. The two thru-hull fittings are installed backwards for shipment. When you receive your reservoir simply unscrew and flip the fittings. Grow plants anywhere! Just attach your Blumat 8mm line, fill with water, and almost instantly your plants are taken care of. This includes two installed Blumat adapters and a black lid. They have two connectors to make it easy to set up a "Blumat Loop" system. With these the water goes from 2 directions effectively giving you twice the capacity. It also equalizes the pressure and is a kind of "insurance policy" - if your line gets kinked, something clogs it up, or someone accidentally puts something heavy on it, all the plants will still get water. These are made from recyclable (#2) HDPE plastic called "the only safe plastic for drinking water" so you don't need to worry about anything bad going to your plants. The black color prevents algae and other nasties from growing in your water and also makes the water going to the roots hotter - a little known secret for superior plant growth.

Read more less

Product Description: This Adjustable Pressure Reducer gives you full control over your Blumat system pressure—ideal for consistent performance and the flexibility to fine-tune your setup. It includes a 0–30 PSI pressure gauge, so you always know exactly what your system is running. This is one of the most important numbers to know in a Blumat setup, essential for troubleshooting and dialing in optimal performance. With a high flow rate of over 5 gallons per minute, this reducer can replace six or more standard Blumat pressure reducers. It’s powerful enough for the largest systems, yet adjustable and precise enough to use with small, single-zone setups as well. The pressure can be set anywhere from 2–14 PSI, allowing you to match system pressure to your specific needs. Different distribution methods (drippers, drip rings, BluSoak) and sensor counts may benefit from different pressure settings, and this reducer gives you the control to optimize performance. Pressure is adjusted by turning the black collar: Left (counterclockwise) = less pressure Right (clockwise) = more pressure Connections & Adapters:The reducer body has a ½" male pipe thread (MPT) inlet and a ¾" female pipe thread (FPT) outlet. Included adapters make it easy to install: Input: Adapts to ¾" female hose thread (FHT) for standard garden hoses or hose bibs Output: ½" Perma-Loc fitting (for Trunk Line Kits) 8mm barb adapter (for Supply Line Kits with Superflex tubing)

Read more less