A research-based guide to capillary mat irrigation: how bottom-up watering works, university findings on water savings, applications, installation, and AquaMat systems.
Capillary mat irrigation waters plants from below using an absorbent fabric that distributes moisture beneath pots and propagation trays. Water moves from the mat into compatible growing media by capillary action. University and peer-reviewed research shows that correctly designed systems can reduce water use, nutrient runoff and watering labor, although results depend on the mat, containers, irrigation controls and growing conditions.
This research-based guide covers how capillary mats work, scientific water-saving results, system construction, applications in nurseries and houseplants, and moisture-controlled AquaMat systems.
What is a capillary mat—and how does it work?
A capillary mat is a porous fabric that absorbs, holds and distributes water beneath containers. Moisture travels through the mat and rises into potting media through connected pores. The pot bottom must contact the moist mat and have openings or permeable materials that let water pass into the growing medium.

Three steps describe the process: (1) water enters the mat through a reservoir or tubing; (2) the fabric distributes it across the growing surface; and (3) containers draw moisture upward as conditions permit. Capillary action itself is passive, but water supply to the mat still needs managing. A continuously flooded or exposed mat is not automatically the most efficient system.
What does the research say about water savings?
University of Arizona (2008): Researchers compared capillary mats with overhead irrigation in a retail nursery study. They measured 71% less irrigation water applied in summer and 62% less in winter with the mats. Species responded differently, so the percentages should not be treated as guarantees for every crop or setting. Read the study.
Goodwin et al. (2003): In a controlled container-plant comparison, average water applied per pot per week was 7.13 L with overhead, 2.60 L with drip and 3.30 L with capillary irrigation. The capillary treatment had the lowest measured nitrate and phosphate leaching of the three approaches. Read the research.
USDA SARE nursery project: Combining capillary mats with overhead watering reduced applied water by 63% for small plants in multicell trays in the reported trial. This also illustrates the usefulness of hybrid approaches. View the project.
Important limitation: A 2021 citrus nursery study found that sensor-controlled ebb-and-flow benches used much less water than the continuously supplied capillary mats tested. Mat covering, evaporation and supply controls matter at least as much as the underlying fabric. View the study.
Different capillary mats and ways to supply water

Compare materials by water-holding capacity (often liters per square meter), distribution characteristics, vertical capillary lift, durability and suitability for cleaning. A mat that stores more water is not necessarily the one that distributes it most evenly.
Layers of a capillary mat system
- Waterproof lower layer to contain water and protect the supporting surface.
- Capillary fabric to absorb and distribute moisture.
- Water-distribution tubing to supply the mat when automated.
- Permeable protective top layer to reduce algae, evaporation and root penetration while allowing moisture through.
Distribution tubing can go above the capillary mat layers and can also connect to above-plant watering, but it is normally best positioned beneath the top layer of the capillary mat system.
Manual, reservoir-fed, timer-controlled and moisture-controlled systems
Manual mats need regular filling. Reservoir-fed mats provide water from a shared supply. Timer systems deliver water at set intervals. Moisture-controlled systems change delivery in response to moisture measurements; the location of the sensor is important because a shared sensor cannot measure every individual pot.
Blumat-regulated AquaMat systems

Sustainable Village's AquaMat systems combine capillary fabric with mechanical Blumat regulation. Depending on the kit, a sensor may respond to moisture in a designated control pot or at the mat surface. The mat supplies a group of compatible pots, while the sensor helps regulate replenishment. These mechanical sensors do not themselves require an electronic timer; the water supply may still need appropriate pressure or power.
How do capillary mats compare to drip?
Drip systems have an advantage if big spaces between plants or in the rare instance of a top watering requirement for a specific type of plants. Capillary Mats have a big advantage though in almost every other case.
Where pots are densely grouped, a shared capillary surface can be simple to manage and rearrange. Drip is particularly adaptable to widely spaced plants and individual zones. Ebb-and-flow benches periodically flood and drain, and may be preferable in facilities designed for nutrient-water recirculation. No method guarantees improved performance without correct design and management.
Where capillary mat irrigation works best
Propagation and seedlings
Bottom watering can keep delicate seedlings supplied without disturbing seeds or wetting foliage repeatedly. Good tray-bottom contact and pre-wetted media are essential.
Greenhouses and commercial nurseries

Closely spaced containers can share a growing surface. Level benches, appropriate water distribution, protective coverings and monitoring help avoid dry patches, overwatering and salt buildup.
Landscaping and larger growing installations

Capillary mats are not limited to greenhouse benches: they can also be incorporated into larger planted surfaces and nursery layouts. Tubing may supply the capillary fabric rather than serving only as conventional individual drip emitters.
Houseplants and herbs

Small mats can serve collections of houseplants or herbs, including during travel, when pots have compatible bases and similar moisture requirements. Plants with contrasting water demands are better separated into different zones.
Living soil and bottomless pots

Capillary mats can support consistent moisture in biologically active growing media, but healthy roots still need oxygen. Bottomless and suitable fabric pots can also be used in certain capillary-pot and transplanting systems. See our guide to capillary pots and living soil.
Customer testimonial and installation videos
Watch the customer testimonial excerpt (1:16–2:53). The linked video player is set to stop at the end of the selected segment where embedding is permitted.
How to Install a Capillary Mat Irrigation System — Sustainable Village demonstration.
Capillary Mat Installation with Surface Blumat — installation demonstration.
How to install a capillary mat watering system
- Choose a stable, level bench, tray or growing surface.
- Install a suitable waterproof underlayer.
- Lay the capillary mat according to its material and orientation.
- Position the water-distribution tubing and permeable protective top layer.
- Connect the water supply and pre-wet the mat.
- Use containers with effective bottom contact and appropriately moist growing media.
- Check moisture at several pots and adjust supply for the crop.
- Inspect regularly for algae, root penetration, salt buildup and uneven wetting.
Common problems and what to check
Wet mat, dry pots: look for poor bottom contact, blocked openings or hydrophobic media. Plants staying too wet: reduce supply and check media aeration. Algae: improve light-blocking covers and sanitation. Salt accumulation: monitor fertilizer concentration and growing-medium electrical conductivity. Roots in the fabric: maintain protective top layers and inspect regularly.
Frequently asked questions
Can capillary mats overwater plants?
Yes. A constantly saturated growing medium can leave too little oxygen for roots. The system must balance moisture and aeration.
Do capillary mats save water?
They often can, especially against overhead irrigation, but study results vary widely depending on water-control systems and exposed surface evaporation.
Do they work with fabric pots?
They can when the fabric base and growing medium permit suitable capillary transfer. Test representative pots before scaling up.
Can capillary mats operate without electricity?
Yes, using manual or suitable gravity-fed supplies and mechanical controls. Pumps and some sources still require electricity.
Can liquid fertilizer be used?
Yes, with careful attention to fertilizer concentration, substrate salt distribution, runoff and cleaning.
Choose a system for your growing area
Start with the number and size of your containers, their water demand and the water source available. For an application-specific recommendation, explore Sustainable Village AquaMat systems and capillary irrigation materials.
Research and further reading
- Semananda et al. (2018), A Semi-Systematic Review of Capillary Irrigation. Horticulturae.
- Schuch et al. (2008), Capillary Mats for Maintenance of Plants in the Retail Nursery. HortTechnology.
- Goodwin et al. (2003), Efficiency of Water and Nutrient Use in Containerised Plants. Australian Journal of Experimental Agriculture.
- Ferrarezi et al. (2015), Subirrigation: Historical Overview, Challenges, and Future Prospects. HortTechnology.
- Jani et al. (2021), Automated Ebb-and-Flow Subirrigation Compared With Capillary Mats. Agricultural Water Management.
- UMass Amherst Extension: Subirrigation Systems.
- USDA SARE: Capillary Irrigation for Container Nurseries.
- UK HDC: Capillary Irrigation of Container Grown Nursery Stock.
