Qualifies for Discount
Tropf Blumat 5" Sensor - Case of 50
The Tropf-Blumat (Tropf means drip in German) is a sensor that automatically supplies plants water through its thin tubing. This ceramic cone employs the principle of hydrostatic pressure, that delivers water extremely slowly, and at the plant’s own preferred rate. Allowing each plant to determine its own irrigation schedule. Blumat Sensors can be used as standalone devices or can also be integrated with drip emitters (we call them “distribution drippers”), drip tape (BluSoak), or capillary mats. These three components assist Blumat sensors in going further. While a Blumat typically irrigates a very small area (a 1-gallon container for example), a single Blumat can irrigate entire garden beds when attached to the Blusoak. How It Works Each Tropf Blumat is filled with water and voided of air prior to being connected to a pressurized line (pressure from gravity-feed is adequate). The water inside the Blumat is in a completely sealed environment. The only exposure it has is through the pores in the ceramic cone. As soil surrounding the cone dries It pulls on the moisture inside the cone through osmotic pressure. Since this is a sealed environment and the pressure cannot equalize, this pulls on a plastic diaphragm in the top of the Blumat. When the diaphragm is pulled down, it allows an irrigation tube running through the top of the valve of the Blumat to open and emit moisture. It does this very gradually. As the water is emitted through the Blumat, the moisture is gradually restored to the soil surrounding the porous ceramic. This relieves the pressure difference between the chamber inside the Blumat and the surrounding soil. This stops pulling on the diaphragm, and the diaphragm restores its former position of pinching the irrigation tubing shut. Allowing each plant to determine its own watering schedule. *The brown knob on top of each Tropf Blumat can be individually calibrated to specific plant species, strain/cultivar/varietal, or media. Details Materials Clay Silicone Plastic Dimensions Weight: 1.3oz Total length: 5.2" Max soil depth: 4" Cap width: 1.4" Sensor width: 1" Tubing length: 8" Connectors Fits 8mm Blumat and Superflex tubing. Flow Rate Adjustable Stand Alone Product? No. Requires water source. Instructions Tropf Blumat Instructions Water your garden thoroughly (ideally overnight) before installation. Prep the Carrots: Fill a container with cooled, non-aerated water (if you’re not sure, boil & cool the water first). Separate the ceramic bottoms from the plastic tops, and soak both parts for at least 15 minutes. While holding the green top underwater use a pipette/eyedropper or your thumb to squirt water into the holes in the green cap. You want to displace any small air bubbles stuck in the cap. Hold both cap and ceramic bottom underwater. Confirm the ceramic bottom and cap are both completely void of air, and reassemble the Blumat ceramic bottom with the green cap while both components are still underwater. Soak the assembled Blumat sensors and keep them submerged for a minimum of 15 minutes. Blumat sensors can stay in water indefinitely, but avoid algae growth and light exposure. While the Tropf Blumats are soaking: Connect the 8mm tubing to a reservoir or Blumat Pressure Reducer which has been integrated to a pressurized line. Run the 8mm tubing to your plants. Installation: Water the garden again, and push the Blumat Carrot in where you would like the moisture sensed, ensuring the ceramic cone is completely covered and firmly anchored. Cut the 8mm tubing and insert the 8 x 8 x 3mm tee (included with each Blumat). Slide the 8mm tubing over the 8mm barbs on the tee. For the last carrot, use the elbow insert instead of the tee. Alternatively, keep the tee in place. Use a small amount of 8mm tubing to attach a 8mm shut-off valve following your final Blumat carrot. This will function as an air/debris purge valve. Adjustment: Turn on the water supply and adjust the flow to each Blumat. Open the valve on the Blumat until flow is visible. Keeping the 3mm tubing level with the valve of the Blumat, slowly tighten (turn clockwise) the Blumat until a hanging drop is just achieved. The flow should just be stopped, but do not twist beyond that point for the “hanging drop.” Tighten the valve on the Blumat an additional two triangles. This will roughly calibrate the sensor to keep maintain current moisture levels.* *If using BluSoak drip tape, do not follow this step. Keeping your sensors at the hanging drip is ideal. Monitor: Come back in 12-24 hours, and make adjustments to each Blumat. If a container or area is over-watered, tighten the Blumat valve (turn clockwise). If a container or area is under-watered, open the Blumat valve (turn counter-clockwise). Repeat the previous step until your system is exactly where you’d like it. The Blumat Digital Moisture Meter is a great tool for assisting with this step. Comparison Chart Tropf Blumat Blumat Classic Glass Globe Blumat Bottle Adapter Vacation Ready ✓ ✓ ✓ ✓ Adjustable ✓ ✓ Out-of-Box Ready ✓ ✓ ✓ Custom System Integration ✓ Max. Water Delivery p/ 24 hrs Adjustable/Unlimited 200ml 118ml 200ml Ideal Location to Water Raised Bed/Garden/Potted Plants Houseplant Houseplant Houseplant Additional Info Maintenance Guide to Tropf Blumat Sensors | Irrigation Equipment Blumat Troubleshooting & Operating Tips/Tricks | Irrigation Equipment Video
$444.93
8mm Cross for SuperFlex 8mm tubing
Description8mm Cross that works best our Super-Flex silicon tubing.
$3.15
Blumat GmbH & Co. KG Blumat Glass Plant Self Watering Globes
Not just a beautiful decoration, these glass watering globes include the patented Blumat Bottle Adapters and regulate water flow by soil type and dryness. The perfect solution for taking care of your houseplants, they slowly and steadily provide water without either over or under-watering. A big help both while away on vacation as well as when still at home, they not only give the plants water but also regulate it based on temperature, growth cycles, and size of plant. An automatic plant watering device that requires no power, electricity, batteries, timers, or any other accessories, they can dramatically upgrade your watering schedule. Details Materials Glass Plastic Silicone Clay Dimensions Weight: 18 oz. Total height: 8 & 1/2" Diameter: 4 & 3/8" Volume: 23 fl. oz. Flow Rate Approx. 7 fl. oz. per 24 hours Instructions Fill the glass globe with water. Push the cone downward into the soil. Watch your plant thrive! Comparison Chart Tropf Blumat Blumat Classic Glass Globe Blumat Bottle Adapter Vacation Ready ✓ ✓ ✓ ✓ Adjustable ✓ ✓ Out-of-Box Ready ✓ ✓ ✓ Custom System Integration ✓ Max. Water Delivery p/ 24 hrs Adjustable/Unlimited 200ml 118ml 200ml Ideal Location to Water Raised Bed/Garden/Potted Plants Houseplant Houseplant Houseplant Additional Info More Info Refill the Glass Globe with water as often as needed to keep plants constantly watered. The Glass Globe is an aesthetically-superior option to plastic or wine bottles. This 23 oz (4 3/8") glass globe can deliver about 200 milliliters (.43 pint) during a 24 hour period. Video
$32.39$27.53
Blumat 6 Sensor Drip Irrigation Kit - Gravity
This small kit designed to water up to six plants or 2.5 square meter gardens lets you quickly test out Blumats yourself. Easy to upgrade later by just adding on these Blumat systems can adjust to any plant type or desired moisture level. This specific kit comes with 5" carrots, which are better for smaller potted plants (10 gallons at most). If you have large plants (in 10+ gallon pots), we recommend using 9" carrots, or Maxis, to get water deep into the soil. Increase your yields and decrease grow times. Our fully-automatic, self-watering systems save time, water, and nutrients - and still ensure healthier, more potent, and faster-growing crops. Perfect for landscapers and home gardeners. It is easily installed with a pair of scissors and connects directly to your hose, tap or rain barrel with the help of the Pressure Reducer. This kit includes six, 5" carrots and all parts required for a gravity-fed system. Reservoirs should be at least 3' above ground-level. An optional Pressure Reducer attached to garden hose or faucet can provide enough water for up to 500 Blumat Carrots. If your reservoir does not have a thru-hull installed, you will have to drill a hole into your reservoir bucket and install a thru-hull piece. For our customers' convenience, we also sell 5-gallon reservoirs with thru-hulls already installed. The Tropf Blumat system is great for watering balcony boxes, planters, hanging baskets, and row crops. It fulfills the needs of the plants on an individual basis, regardless of their location, light levels, or plant type. Our systems save your plants from excessive and improper watering. Tropf Blumat systems are ideal for plant groupings that require consistent moisture, such as vegetable gardens, bushes, flower beds, grow bags and greenhouse containers. Not only do your plants receive the right amount of water, slow and consistent dripping ensures that your plants receive warmed water, avoiding shock. This Deck and Planter Kit is a great way to start your customized irrigation system. The flexible system can be expanded to include up to 500 drippers. See 'Blumat Accessories' to expand our systems to your specific needs. How it works The Tropf Blumat self-watering system functions automatically. As the soil dries, a vacuum and hydro-static pressure, coupled with a spring-loaded gating mechanism, pulls water from the main line. When the soil is sufficiently moist, pressures equalize, and the Tropf Blumat automatically stops taking in water. Each Blumat Outdoor Sensor in the Deck and Planter Set covers an area 12 inches in diameter. To expand and customize your own system, add additional Supply Hoses, Outdoor Sensors, and Distributor Drippers. PLEASE NOTE: This system does not include a Pressure Reducer or water source. A pressure reducer is needed if you are connecting your system to a threaded spigot, such as your hose/home water supply or the spigot on a rain barrel or reservoir. Note: Tropf Blumat systems are not recommended for indoor use. If hooked up to a constant water source, a pet, guest, or user-error could causes a run-away, damaging an indoor floor, drywall, carpet, or furniture. For this reason, we recommend Blumat Classics (Juniors) and bottle adapters for houseplants, and Tropf-Blumats for greenhouses, grow rooms, decks, and outside gardens. Please contact us for any help, we are always here to help make your life easier. Components This Kit Includes: 6 Blumat carrots (5") (IG17188) 7 meters (23 feet) of 8mm tubing (IG15634) 1 Tee Splitter (IG17310) 1 Elbow Splitter (IG15595) 1 Hose Coupler (IG15638) 1 Hose End-Piece (IG15986) 1 Rain Barrel/Gravity Tank Connector and Installation Instructions (IG15691) 1 Pipette (IG15651)
$66.00
Sun-Mar Microbe Mix
100% natural blend of microbes and enzymes Starts and accelerates composting in all composting toilets Use in mulch and sprinkled on soil to increase beneficial microbe support Also great for compost bins and piles Use in mulch and sprinkled on soil to increase beneficial microbe support One jar lasts for months or years This compost accelerator is designed to initiate and accelerate composting. These microbes will help with the composting process wherever they are! Add these to your compost bucket, composting bin, compost tea brewer, worm composter, etc. These will enhance the organic compost process wherever they are. They will enhance and speed composting in tumblers, compost piles, and you can even add these microbes to your soil. This unique blend of microbes and enzymes will enhance/accelerate composting and reduce unwanted odors in garden beds, garden composters, compost piles, natures head composting toilet(s), pet waste piles, composting worms, bokashi compost piles, bokashi compost starter kit(s), and more. You could even inoculate your drip irrigation kit, garden watering system, or other irrigation system (we recommend Blumat) with these microbes to enhance biological soil activity. We have even seen success by adding this blend directly to a drip system or garden irrigation system. Your compost worms will love this stuff! Applying these microbes is incredibly simple and easy! Just sprinkle some of the dry granular wherever they are needed, and they will do the rest of the work. These are especially effective in self-contained composting toilet units and similar systems that are dependent on microbiological activity for composting and keeping unwanted odors away. MICROBE MIX The perfect (as far as we know) combination of dried microbes and enzymes to assure the best start and speed for this kind of composting. Sun-Mar recommends using this every 2 weeks which will make these 18 oz. jars last 6 months.
$28.00
Blumat 3mm Y connector
Description Use these to extend the 3mm Blumat Junior lines and have more than one working from the same water source without creating a "spaghetti" effect.You can also add them to an outside Tropf Blumat system when a T is too wide - great for running Blumat distributors on both sides of a row of plants.
$1.04
3mm Tees
Description Use these to branch out and run distribution drippers in two directions. You can also put them directly into a 1/2" or 3/4" drip line and install two Blumat sensors.
$1.30
BluSoak Drip Tape Coupling
Description Join two lengths of Blu Carrot Soaker Hose together. Link to Soaker Hose Benefits Video
$1.08
Blumat Irrigation for Pots
Build the exact Blumat irrigation kit your pots need — from 1-gallon seedling containers to 200-gallon living soil setups. Choose your sensor size, calibration type, and water distribution method. No timers, no electricity, no daily watering. Sensor Size ＋ 5" Sensor — Senses moisture at the soil surface. Best for pots under 10 gallons or shallow-rooted crops. 9" Sensor — Adjustable depth up to 9 inches. Better moisture control for larger containers and deep root zones. Calibration Type ＋ Standard — Ships as-is from Blumat. You dial in the moisture level yourself. Includes 6" of 3mm tubing (5" sensor) or 2 ft (9" sensor). Preset — Pre-calibrated at the factory for most soil and potting mix types. Just insert and go. Includes locking adjustment cap, 3mm union, adjustment key, and extra 2 ft of 3mm tubing. Distribution Method ＋ None (1–5 gal) — Sensor waters directly at the insertion point. Best for small pots. 5" Drip Ring (2–7 gal) — 4 drip points, pre-assembled. 3-Dripper Setup (5–20 gal) — 3 drippers with stakes and 3mm tubing. 10" Drip Ring (10–20 gal) — 8 drip points, pre-assembled. 5-Dripper Setup (10–30 gal) — 5 drippers with stakes and 3mm tubing. BluSoak Tape Loop (30–90 gal) — Single loop for even coverage around large containers. BluSoak Tape Double Spiral (30–90 gal) — Spiral from center outward for maximum coverage. BluSoak Tape Triple Spiral (100–200 gal) — Largest spiral layout for very big pots and beds. What's Included ＋ 1 Blumat sensor (5" or 9" based on selection) 3mm drip tubing (6" or 2 ft based on sensor size) Distribution components based on selection (drip ring, drippers, or BluSoak tape) Preset upgrade includes: locking adjustment cap, 3mm union, adjustment key, extra tubing What You'll Also Need ＋ This kit covers everything at the pot. To complete your system you’ll also need an 8mm supply line and a water source: 8mm Supply Line — runs from your water source to the sensor. See our 8mm SuperFlex Supply Line Kits. Gravity Reservoir — our complete 5-Gallon Deluxe Bucket Kit comes pre-drilled and ready to connect, or grab our 8mm Bulkhead Fittings and use any container of your choosing. Pressurized Source (hose bib or pump) — if connecting to a hose bib or pump instead of a gravity reservoir, you’ll need a Pressure Reducer to bring the pressure down to the safe Blumat operating range of 7–15 PSI. How It Works ＋ The Blumat sensor is a ceramic cone that reads soil moisture. As the soil dries, a vacuum builds inside the cone and pulls water through the drip line. When moisture is restored, the valve closes automatically. Connect your sensor to any 8mm Blumat supply line running from a gravity reservoir or pressurized source. No programming, no timers, no electricity required.
$9.18 - $39.96
Perma-Loc 1/2" Elbow
Connect two pieces of 1/2" tubing at a 90° angle.
$3.23
Whole System Adjustable Pressure Reducer for Blumat systems
Full control over your Blumat system pressure. Adjustable from 2–14 PSI with a built-in gauge so you always know exactly what your system is running — the most important number to know in any Blumat setup. Key Features ＋ Built-in 0–30 PSI pressure gauge for real-time monitoring High flow rate of over 5 gallons per minute — can replace six or more standard Blumat pressure reducers Adjustable from 2–14 PSI to match any distribution method (drippers, drip rings, BluSoak) Powerful enough for the largest systems, precise enough for single-zone setups Connections & Adapters ＋ The reducer body has a ½" male pipe thread (MPT) inlet and a ¾" female pipe thread (FPT) outlet. Included adapters make it easy to install: Input — ¾" PVC swivel adapter for standard garden hoses or hose bibs Output — ¾" to ½" Perma-Loc fitting for Trunk Line Kits Output — ¾" to 8mm adapter for Supply Line Kits with SuperFlex tubing Also includes — ¾" FPT tee and 1/4" to ¾" MBT bushing Installation Instructions ＋ Tape all male fittings with the provided tape, wrapping 5–6 times clockwise. Assemble parts as pictured in the instruction diagram. Connect to a valve on a pump kit or to a hose bib using the provided ¾" swivel adapter. Using the provided fittings, connect to your Blumat system supply line. Open the incoming water to check current system pressure. Recommended ranges: Drip rings — 12–15 PSI BluSoak — 7–10 PSI To adjust pressure: turn off incoming water, release system pressure by opening a valve on the Blumat supply line until the gauge reads 0, then turn the black adjustment collar (tighten for more pressure, loosen for less). Close the Blumat supply line valve and open incoming water to re-pressurize. Check the gauge. If not in range, repeat steps 6–7 until correct.
$140.40
Adapter - 1/2" MPT to 8mm Barbed for Blumat Systems
Description Easiy attach Blumat 8 mm tube to irrigation line, PVC, or even a garden hose (with a hose to pipe adapter). This has a male insert fitting for the 8 mm tube and a 1/2" male pipe thread on the other
$2.16
Blumat 3mm Tee - 3 Pack
Description Multi-use tee connectors for the 3 mm line that comes with each Blumat carrot. Use these to send distribution drippers in different directions, to connect into drip tubing and give water to 2 carrots, and to make watering circles around plants.
$3.68
Brass, Copper and Nickel Plant Misters
This classic looking solid metal mister, sprays water in fine and small amounts, while being aesthetically-pleasing and pragmatic. The spray is great for keeping plants clean from dust, for increasing humidity, or even for spraying fertilizer if needed. The comfortable handle makes daily misting easy. Some of the best sprayers are those that can live in close proximity to the plants for convenient regular misting. For that, the mister needs to look nice enough for display like this model. With its stainless steel and polished copper finish, this metal spray mister holds its own next to a prized orchid or bonsai tree. The 10-ounce spray mister comes in copper, brass, or nickel. Details Materials Metal Plastic Rubber Dimensions Weight: 0.3 lb. Total height: 6" Diameter: 3.5" Volume: 10 fl. oz. Plant Mister Instructions: To use the metal mister, fill with water, hold the small loop handle with the fingers then depress the top with the thumb to release a fine mist. Video
$27.00 - $61.24
Blumat 12 Sensor Drip Irrigation Kit - Gravity Deluxe
Our medium kits are designed to water areas up to 3.5 square meters, or 12 potted plants. As an upgrade from the popular standard medium kit, our deluxe kit includes parts to make a continuous loop, which equalizes water pressure and always assures partial water flow - even if some of the tubing gets clogged, kinked or blocked. This kit is meant to be hooked up to a gravity system, and includes the bulkhead fitting to be hooked up to your reservoir. It also includes a pipette and a valve to let out air bubbles and sediment. Blumat systems can adjust to any plant type or desired moisture level. This specific kit comes with 5" carrots, which are better for smaller potted plants (10 gallons at most). If you have large plants (10+ gallon pots), we recommend using 9" carrots, or Maxis, to get water deep into the soil. Increase your yields and decrease grow times. Our fully-automatic, self-watering systems save time, water, and nutrients - and still ensure healthier, more potent, and faster-growing crops. Perfect for landscapers and home gardeners. It is easily installed with a pair of scissors and connects directly to your hose, tap or rain barrel with the help of the Pressure Reducer. This kit includes twelve, 5" carrots and all the parts required for a gravity-fed system. Reservoirs should be at least 3' above ground-level. An optional Pressure Reducer attached to garden hose or faucet can provide enough water for up to 500 Blumat Carrots (See 'Related Products'). If your reservoir does not have a thru-hull installed, you will have to drill a hole into your reservoir bucket and install a thru-hull piece. For our customers' convenience, we also sell 5-gallon reservoirs with thru-hulls already installed. The Tropf Blumat system is great for watering balcony boxes, planters, hanging baskets, and row crops. It fulfills the needs of the plants on an individual basis, regardless of their location, light levels, or plant type. Our systems save your plants from excessive and improper watering. Tropf Blumat system are ideal for plant groupings that require consistent moisture, such as vegetable gardens, bushes, flower beds, grow bags and greenhouse containers. Not only do your plants receive the right amount of water, slow and consistent dripping ensures that your plants receive warmed water, avoiding shock. This Deck and Planter Kit is a great way to start your customized irrigation system. The flexible system can be expanded to include up to 500 drippers. See 'Blumat Accessories' to expand our systems to your specific needs. PLEASE NOTE: Tropf Blumat systems do not include a Pressure Reducer. You will need this if you are connecting your system to a threaded spigot, such as your hose/home water supply or the spigot on a rain barrel or reservoir. The Pressure Reducer is in 'Related Products' below. This system does not include a water source. See 5-gallon Reservoirs below, sold with or without thru-hulls installed. Let us know if we can help you select the right products for your custom irrigation system! Components This Kit Includes: 12 Blumat Carrots (5") (IG17188) 3 Blumat Tees (8mm-to-3mm) (IG15653) 7 Meters (23 Feet) of Superflex Tubing (IG16694) 2 Blumat Tee Splitters (IG17310) 1 Elbow Splitter (IG15595) 1 Hose Union (IG15638) 1 Hose End-Piece (IG15986) 2 Rain Barrel/Gravity Tank Connectors (IG15691) 1 8mm Shut-Off Valve/Air Purge (IG15697) 1 Plastic Pipette (Removes Bubbles from Blumats To Ensure Proper Function) (IG15651)
$122.00
Perma-Loc 1/2" Tee
Connect three pieces of drip tubing in "T" shape.
$4.29
8mm BULKHEAD / Through-Hull Tank Connector - 4 Pack
Description 4 Blumat Thru-Hull Tank Connectors to attach 8 mm Blumat water supply line to a rain barrel or water storage tank. This is your classic bulkhead fitting, made in Austria, high quality and efficient for a Blumat System. Bulkhead fittings allow you to penetrate through a wall or barrier, while allowing passage within the fitting. This allow you to tap into a tank of water, while allowing water to pass-through the bulkhead fitting, and into a water supply line. We have these pre-drilled into our 5-gal bucket reservoir, see related products below. Have your own reservoir? No problem, simply drill 1/2" holes into your own water tank and convert it into a Blumat Reservoir. We have even higher quality bullhead fittings, some that stop water flow when disconnected. Check out our bulkhead fittings category. *Reservoir not included, look into Blumat Reservoir or 5-gal bucket if you need a reservoir
$21.01
Blumat Distibution Drippers (Ten) + 2m of Drip tube - 2 Pack
Description These are great for watering long plant beds, planter boxes, and giving large plants an even amount of water in a circle around them. They connect to a Tropf-Blumat or a Maxi.This is less expensive than adding more sensors but you may need to add a filter to your system if you use nutrients in your water so they don't clog. Two barbs let you connect tubing on both sides of the dripper for up to five drip locations from one Tropf-Blumat (dripper chain). The end-distributor dripper has a drip nozzle on one side only for use as the end piece in a dripper chain. You can go as far as 100 cm (39") from the sensor with these and they water about 20 cm wide (8"). Minimum pressure to use them like this is 4.5 psi. You can go down as low as 2 psi but the last dripper or two might not put out much water. By adjusting the black screw on the top, you can use more. In pressure systems, customers report successfully using as many as 25 with just one Blumat sensor.
$43.32
3mm Quick Connect On/Off Valve
Description Use a 3mm quick-connect to turn the water from your supply line either on or off. Conveniently connect different fittings to serve different functions. Use a 3mm to 8mm to connect your main water line to your Blumat carrot line. Fit a 3mm to 3mm quick connect to turn the water going directly into your Blumats either on or off. Adapt a 1/4" drip line to the Blumat 8 mm tubing - quick and easy with this handy connector. Later if you like, you can change either side and go to 3 mm, 1/4, or 8 mm. These high quality quick connect can be implemented in a number of ways and are recommended for all watering systems to make your life easier.
$5.13
Blumat Stops, sealing caps
Cap off any of the 3 mm Blumat barbs - the distribution drippers, Tees, or connectors.
$0.43
Blumat Digital Moisture Meter - Top Replacement Only
The Blumat Digital moisture meter is a super accurate water moisture reader that measure the moisture content of your plant at root level. This is the replacement top for the moisture meter and is great for making an old item brand new! DO NOT WET THE DISPLAY. Moisture can cause damage to the LCD display. If using outside or in conjunction with hand-watering or foliar feeds, use our cap here.
$66.00
Blumat Elbows - 3 Pack
Description These really help in greenhouses and raised beds. They help you neatly go around corners in your Tropf Blumat irrigation system. The right-angled elbow eliminates bends in the tubing that can limit the flow in your irrigation system. The black plastic is robust and barbed at both ends to hold the tube securely in place. Contains three 8mm (5/16") elbows.
$4.32
Preset Blumat Grow Tent Irrigation Kit
The Grow Tent Preset Blumat Irrigation Kit is a complete, ready-to-install Blumat system designed specifically for indoor grow tents and living soil setups. These kits are built around preset Blumat sensors, which means you get the benefits of plant-driven automation without the confusing setup process. Once installed, your system will maintain stable soil moisture automatically — no timers, no hand watering schedules, and no daily guesswork. Preset Blumat sensors are designed for a fast, repeatable setup. Instead of spending time calibrating and second-guessing adjustments, you can get up and running quickly while still getting the reliable, plant-controlled performance Blumat is known for.
$89.00 - $274.00
Maxi Spiral 30-90 Gallon Pot
Description This kit provides an easy, fast, and water-saving way to water a 30-90 gallon pot. No timers, batteries, or electricity required! Click here to download the instructions. This system utilizes a Blumat carrot (sensor) to automatically water and monitor the moisture levels in your garden soil. BluSoak tape allows for even water distribution throughout. When coupled together with Blumat carrots, BluSoak hose only delivers water to your veggies when they need it, which promotes exponential growth and impressive yields. You can also leave your BluSoak tape under your garden all winter, no problem. Water source needs to be 6-10' above the garden for a gravity system. For a pressure system running off a faucet or garden hose, simply add a Blumat Pressure Reducer.What You Might Need (Not included in kit): Connection to your water source (either thru-hull bulkhead fitting for gravity systems, a pressure reducer, or a Blumat pump for larger systems) 8mm Supply tube to connect your water source to your Blumats Additional Hold-Down stakes or 3mm tubing Fittings (tee's, elbows, couplers, etc.) How it works The Tropf Blumat self-watering system functions automatically. As the soil dries, a vacuum and hydro-static pressure, coupled with a spring-loaded gating mechanism, pulls water from the main line. When your soil is sufficiently moist, pressures equalize, and the Tropf Blumat automatically stops water flow. Essentially, water will seep through your BluSoak hose only when your plants need it, thanks to Blumat technology. For a gravity-fed system, you'll need a reservoir. See 5-gallon Reservoirs below, sold with or without thru-hulls installed. Let us know if we can help you select the right products for your custom irrigation system! Need a reservoir? Link to product page here *Note: If ordering more than a quantity of two, we will pack together a sample kit with the contents of the kit, but the rest will come in bulk packaging (we do this in order to ship items out in time, rather than to delay shipments). You may special request for all items to be packaged independently, but extra costs may apply. Components This Kit Includes: 1 Blumat Maxi Carrot (IG14618) 6 feet BluSoak 2.0 Drip Tape (IG18206) 1 BluSoak Fittings (Tape To Sensor) (IG14607) 1 BluSoak End Plug (To End Drip Tape) IG16065 *Customer assembly is required.
$23.64
What Growers Are Saying
