Home - Top Selling Products

Build the exact Blumat irrigation kit your pots need — from 1-gallon seedling containers to 200-gallon living soil setups. Choose your sensor size, calibration type, and water distribution method. No timers, no electricity, no daily watering. Sensor Size ＋ 5" Sensor — Senses moisture at the soil surface. Best for pots under 10 gallons or shallow-rooted crops. 9" Sensor — Adjustable depth up to 9 inches. Better moisture control for larger containers and deep root zones. Calibration Type ＋ Standard — Ships as-is from Blumat. You dial in the moisture level yourself. Includes 6" of 3mm tubing (5" sensor) or 2 ft (9" sensor). Preset — Pre-calibrated at the factory for most soil and potting mix types. Just insert and go. Includes locking adjustment cap, 3mm union, adjustment key, and extra 2 ft of 3mm tubing. Distribution Method ＋ None (1–5 gal) — Sensor waters directly at the insertion point. Best for small pots. 5" Drip Ring (2–7 gal) — 4 drip points, pre-assembled. 3-Dripper Setup (5–20 gal) — 3 drippers with stakes and 3mm tubing. 10" Drip Ring (10–20 gal) — 8 drip points, pre-assembled. 5-Dripper Setup (10–30 gal) — 5 drippers with stakes and 3mm tubing. BluSoak Tape Loop (30–90 gal) — Single loop for even coverage around large containers. BluSoak Tape Double Spiral (30–90 gal) — Spiral from center outward for maximum coverage. BluSoak Tape Triple Spiral (100–200 gal) — Largest spiral layout for very big pots and beds. What's Included ＋ 1 Blumat sensor (5" or 9" based on selection) 3mm drip tubing (6" or 2 ft based on sensor size) Distribution components based on selection (drip ring, drippers, or BluSoak tape) Preset upgrade includes: locking adjustment cap, 3mm union, adjustment key, extra tubing What You'll Also Need ＋ This kit covers everything at the pot. To complete your system you’ll also need an 8mm supply line and a water source: 8mm Supply Line — runs from your water source to the sensor. See our 8mm SuperFlex Supply Line Kits. Gravity Reservoir — our complete 5-Gallon Deluxe Bucket Kit comes pre-drilled and ready to connect, or grab our 8mm Bulkhead Fittings and use any container of your choosing. Pressurized Source (hose bib or pump) — if connecting to a hose bib or pump instead of a gravity reservoir, you’ll need a Pressure Reducer to bring the pressure down to the safe Blumat operating range of 7–15 PSI. How It Works ＋ The Blumat sensor is a ceramic cone that reads soil moisture. As the soil dries, a vacuum builds inside the cone and pulls water through the drip line. When moisture is restored, the valve closes automatically. Connect your sensor to any 8mm Blumat supply line running from a gravity reservoir or pressurized source. No programming, no timers, no electricity required.

Read more less

Build the exact Blumat raised bed kit you need. Choose your bed size, sensor setup, and calibration type. BluSoak drip tape delivers even, low-pressure watering across the full bed — automatically, based on soil moisture. Bed Size & Layout ＋ 2 Row (2×4 ft) — Two rows of BluSoak drip tape 3 Row (3×3 ft) — Three rows of BluSoak drip tape 3 Row (3×6 ft) — Three rows of BluSoak drip tape 4 Row (4×4 ft) — Four rows of BluSoak drip tape 4 Row (4×8 ft) — Four rows of BluSoak drip tape Sensor Type ＋ 5" Sensor — Senses moisture at the surface. Best for beds 8" deep or less with shallow-rooted crops. 9" Sensor — Adjustable to depths up to 9". Better for deeper beds and more dynamic moisture control. 5" + 9" Dual Sensor — Two sensing depths working in tandem for the most precise moisture response. Calibration Type ＋ Standard — Ships as-is from Blumat. You dial in moisture yourself. Includes 6" of 3mm tubing (5" sensor) or 2 ft (9" sensor). Preset — Pre-calibrated at the factory. Just insert and go. Includes locking adjustment cap, 3mm union, and adjustment key. What's Included ＋ Blumat sensor(s) based on selection BluSoak drip tape rows sized to your bed All BluSoak fittings and adapters 3mm drip tubing Preset upgrade includes: locking cap, 3mm union, adjustment key What You'll Also Need ＋ This kit covers everything inside the bed. To complete your system you'll also need an 8mm supply line and a water source: 8mm Supply Line — runs from your water source to the sensor. See our 8mm SuperFlex Supply Line Kits. Gravity Reservoir — our complete 5-Gallon Deluxe Bucket Kit, or use our 8mm Bulkhead Fittings with any container of your choosing. Pressurized Source (hose bib or pump) — requires a Pressure Reducer to bring pressure down to the safe Blumat range of 7–15 PSI. How It Works ＋ The Blumat sensor reads soil moisture and controls water flow through the BluSoak drip tape. As the bed dries, the sensor opens and water flows. When moisture is restored, it closes automatically. No timers, no electricity, no programming. Works with both gravity and pressurized water sources.

Read more less

Take the guesswork out of watering with AquaMat Capillary Mat Kits — designed for consistent, bottom-up hydration that accelerates vegetative growth and increases soil aeration. Each kit is fully customizable. Choose your mat size, irrigation control method, and container option. Mat Size Options ＋ 2×4 ft 3×3 ft 4×4 ft 4×8 ft Irrigation Control Options ＋ Preset 5" Blumat Sensor — Placed into a pilot container filled with soil, this sensor regulates water flow into the mat based on soil moisture levels. Best suited for pots 4" or larger. Surface-Mounted Blumat — A bell-shaped ceramic base that attaches to a Blumat sensor and sits directly on the mat. Fine-tune moisture levels for uniform watering across the surface. Ideal for cell trays or small containers. No Sensor — For manual watering. No fittings included. Container Options ＋ Grassroots 1-Gallon Bottomless Sleeves — Maximize aeration and allow roots to grow through the open base into the mat. Ideal for easy transplanting. (10 for 2×4, 20 for 3×3 or 4×4, 40 for 4×8) Non-Woven Nursery Pots — Biodegradable, tear-resistant fabric bags that allow roots to grow through the sides and bottom for easy transplanting. (50 with any mat size) None — Use your own containers. Any pot with holes flush to the bottom will work. What You'll Also Need ＋ This kit covers the mat and containers. To complete your system you'll also need an 8mm supply line and a water source: 8mm Supply Line — runs from your water source to the sensor. See our 8mm SuperFlex Supply Line Kits. Gravity Reservoir — our complete 5-Gallon Deluxe Bucket Kit, or use our 8mm Bulkhead Fittings with any container of your choosing. Pressurized Source (hose bib or pump) — requires a Pressure Reducer to bring pressure down to the safe Blumat range of 7–15 PSI.

Read more less

The ultimate upgrade for a Blumat system. The Mini Pump Kit converts your gravity-fed setup into a pressurized irrigation system — faster sensor response, more consistent moisture levels, and the freedom to run a large reservoir on the ground without elevation. Once you run Blumat on pressure, it's very hard to go back. Why Pressure Changes Everything ＋ Blumat systems are pressure-sensitive. Gravity setups can work well, but they often introduce slow response times and small inconsistencies. When you switch to pressure, the entire system tightens up: Faster sensor response to soil moisture changes Adjustments show results much more quickly More consistent moisture levels across your grow More reliable overall system performance What's Included ＋ Mini pump Expansion / pressure tank Adjustable pressure reducer with integrated gauge Inline filter Bulkhead fitting for reservoir connection All tubing and hardware to connect to your reservoir Adapter for 8mm tubing or 1/2" black poly via Perma-Loc fitting System Size & Capacity ＋ Ideal for small tents and home grows Scales to multi-tent setups Rated for up to approximately 50 gallons per day Suitable for larger rooms when properly designed Frequently Asked Questions ＋ Do I need a pump for a small Blumat system?No — but even small systems benefit from faster response and more consistent performance when running on pressure. Can I use a larger reservoir with this system?Yes. One of the biggest advantages is being able to run a large reservoir on the ground instead of elevating it. What's the benefit of switching from gravity to pressure?Faster sensor response, more stable moisture levels, better system control, and reduced maintenance.

Read more less