{"title":"Pressure Reducers","description":"\u003ch2\u003eChoose the Right Pressure Reducer for Your Blumat System\u003c\/h2\u003e\u003cp\u003eA true pressure reducer lowers incoming water pressure to a safe, stable operating range for Blumat irrigation. These are not simple flow restrictors. Choose your reducer based on the pressure you want to run and the size of the supply connection feeding your system.\u003c\/p\u003e\u003ch3\u003eQuick Selection Guide\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.5 bar \/ 7.3 PSI:\u003c\/strong\u003e Best for standard gravity-style performance from a pressurized water source and for growers who want a gentler operating pressure.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1 bar \/ 15 PSI:\u003c\/strong\u003e Best for faster sensor response, larger systems, and high-pressure Blumat setups. Do not operate standard Blumat components above 15 PSI.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e8mm output:\u003c\/strong\u003e Best for smaller systems where the reducer connects directly to 8mm Blumat supply tubing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e3\/4-inch output:\u003c\/strong\u003e Best for larger systems that need higher flow before transitioning into a trunk line or multiple zones.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWhole System Adjustable Pressure Reducer:\u003c\/strong\u003e Best when you want a visible pressure gauge and the ability to fine-tune the entire system between approximately 2 and 14 PSI.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhich One Should You Choose?\u003c\/h3\u003e\u003cp\u003eFor most small indoor systems, use an 8mm-output reducer. For larger gardens, multiple zones, or long supply runs, use a 3\/4-inch-output reducer or the Whole System Adjustable Pressure Reducer before reducing down to your Blumat supply lines.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation note:\u003c\/strong\u003e Install the pressure reducer before the 8mm supply line. Keep final operating pressure at or below 15 PSI.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCollection page requirement:\u003c\/strong\u003e Display an add-to-cart buy box and quantity selector directly with each product whenever the collection template supports it.\u003c\/p\u003e","products":[{"product_id":"ig14606","title":"Blumat Standard Pressure Reducer 1bar (15psi)","description":"\u003cdiv style=\"max-width: 680px; line-height: 1.7;\"\u003e\n  \u003cp style=\"font-size: 1.05rem; color: #3a3a3a; margin-bottom: 1.5rem;\"\u003eA true pressure reducer — not a flow controller. Drops incoming water pressure down to 15 PSI (1 bar), the safe operating range for all Tropf Blumat sensors and BluSoak systems. Screws onto any standard 3\/4\" hose bib and outputs directly to 8mm Blumat supply tubing.\u003c\/p\u003e\n\n  \u003cdetails style=\"border-top: 1px solid #d4c9b0; margin-bottom: 0;\"\u003e\n    \u003csummary style=\"cursor: pointer; padding: 1rem 0; font-size: 0.95rem; font-weight: 700; letter-spacing: 0.08em; text-transform: uppercase; list-style: none; display: flex; justify-content: space-between; align-items: center;\"\u003eKey Features \u003cspan style=\"font-size: 1.2rem; font-weight: 300;\"\u003e＋\u003c\/span\u003e\u003c\/summary\u003e\n    \u003cdiv style=\"padding-bottom: 1.2rem; color: #3a3a3a;\"\u003e\n      \u003cul style=\"margin: 0; padding-left: 1.2rem; line-height: 2;\"\u003e\n        \u003cli\u003eTrue pressure reducer — actually lowers system pressure, not just flow rate\u003c\/li\u003e\n        \u003cli\u003eFixed output of 15 PSI (1 bar) — the ideal operating pressure for Blumat systems\u003c\/li\u003e\n        \u003cli\u003eMaximum input pressure of 87 PSI\u003c\/li\u003e\n        \u003cli\u003e3\/4\" female hose thread input — connects to any standard hose bib or faucet\u003c\/li\u003e\n        \u003cli\u003e8mm barb output — connects directly to Blumat supply tubing, no tools needed\u003c\/li\u003e\n        \u003cli\u003eMade from ABS plastic, Austrian-engineered, designed for long-term reliability\u003c\/li\u003e\n      \u003c\/ul\u003e\n    \u003c\/div\u003e\n  \u003c\/details\u003e\n\n  \u003cdetails style=\"border-top: 1px solid #d4c9b0; margin-bottom: 0;\"\u003e\n    \u003csummary style=\"cursor: pointer; padding: 1rem 0; font-size: 0.95rem; font-weight: 700; letter-spacing: 0.08em; text-transform: uppercase; list-style: none; display: flex; justify-content: space-between; align-items: center;\"\u003eWhy a True Reducer Matters \u003cspan style=\"font-size: 1.2rem; font-weight: 300;\"\u003e＋\u003c\/span\u003e\u003c\/summary\u003e\n    \u003cdiv style=\"padding-bottom: 1.2rem; color: #3a3a3a;\"\u003e\n      \u003cp style=\"margin: 0 0 0.8rem;\"\u003eMany products sold as pressure reducers are actually flow controllers — they restrict flow but don't lower actual system pressure. Reduced flow does not equal reduced pressure.\u003c\/p\u003e\n      \u003cp style=\"margin: 0;\"\u003eThis is a genuine pressure reducer that brings any incoming supply down to a safe 15 PSI output regardless of flow. Running Blumat sensors above 15 PSI risks pushing tubing connections apart and flooding. This is the component that prevents that.\u003c\/p\u003e\n    \u003c\/div\u003e\n  \u003c\/details\u003e\n\n  \u003cdiv style=\"border-top: 1px solid #d4c9b0;\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Sustainable Village","offers":[{"title":"Blumat Standard Pressure Reducer 1bar (15psi)","offer_id":42915601121466,"sku":"IG14606","price":59.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0637\/4722\/7834\/files\/IG14606.all-01.png?v=1707424535"},{"product_id":"ig16242","title":"Blumat Pressure Reducer, 0.5 bar (7.3 psi)","description":"\u003cdiv id=\"sv-product-tabs\"\u003e\n\u003ch5\u003eDescription\u003c\/h5\u003e\n\u003cul\u003e \u003cli\u003eTrue reducer - Not a mere flow controller, this brings water pressure down to 7.25 psi (0.5 bar)!\u003c\/li\u003e \u003cli\u003eEasy to install - Screws onto standard hose thread (3\/4\" input), and outputs to 8mm tubing!\u003c\/li\u003e \u003cli\u003eEnduring - Made from ABS plastic and designed with few points of failure, this is built to last!\u003c\/li\u003e \u003cli\u003eBlumat ready - Designed specifically for Blumat water systems and 8mm tubing, no tools necessary!\u003c\/li\u003e \u003cli\u003eAustria-engineered - This is high-quality component and is designed and manufactured by clever Austrians!\u003c\/li\u003e \u003cli\u003eBlumat systems need low pressure, much less than comes from a normal house water connections. The Blumat Pressure Reducer allows for easy integration of a municipal (or otherwise pressurized line, such as from a well) water line into a blumat, blusoak, or easysoak watering system.\u003c\/li\u003e \u003c\/ul\u003e\n\u003cbr\u003e  \u003cp\u003eBeware imposters! Many pressure reducers are not real pressure reducers at all, but are merely flow controllers, and reduce flow rates. However, reduced flow rates do not necessarily correlate to reduced pressure. This is a true pressure reducer, and will reduce any incoming water (with a maximum pressure input of 87 psi) down to 7.25i (0.5 bar) output. This is ideally suited and low enough for Blumat systems and their components. Higher pressure will push tubing connections apart, and increase likelihood of flooding. This pressure reducer is extremely easy to use. The input side screws onto a standard 3\/4\") hose bibb or hose threading, often found on taps outside the home, or even faucets inside the home. The output side (featured with collar) is ideally suited for 8mm tubing (I suggest using our super-flex tubing). This is the size that integrates directly with Tropf Blumats. This adaptation makes setting up a Blumat system from a hose or pressurized line an absolute breeze, and you can install blumats in seconds.\u003c\/p\u003e \u003cp\u003eBlumat systems need low pressure, much less than comes from a normal house water connections. Some of our kits include one of these but if you'd like to install the other ones or the separate components to a home water system, you'll need one of these Pressure Reducers.\u003c\/p\u003e \u003cp\u003eIn gravity systems you'll also need one if your storage tank is high uphill. In Grow Rooms and Greenhouses with a reservoir for mixing nutrients, you can connect a small pressure pump to this and automatically feed your plants when you water. On one side it adapts to a 3\/4\" male hose thread and on the other directly to a Blumat 8mm supply tube. Maximum input pressure is 87 psi.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Blumat GmbH \u0026 Co. KG","offers":[{"title":"Default Title","offer_id":42915683238074,"sku":"IG16242","price":69.58,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0637\/4722\/7834\/files\/139996.jpg?v=1760381317"},{"product_id":"ig18537","title":"Blumat Pressure Reducer 15 psi - 3\/4\" MHT output","description":"\u003cdiv id=\"sv-product-tabs\"\u003eThe standard Blumat pressure reducers work great for most systems. But for larger systems that need a higher flow rate, this becomes a better choice. This also works better when there's a long distance between the pressure reducer and your plants.\u003cbr\u003e\u003cbr\u003eA TRUE REDUCER - Not just a flow controller that only works with high flows, these reduce pressure in Blumat systems with extremely low flow rates\u003cbr\u003eEASY TO INSTALL - Uses standard 3\/4\"\" hose thread for both input and ouput sides\u003cbr\u003eHIGH QUALITY - Built to last from ABS plastic and designed for longest life \u003cbr\u003e\u003cbr\u003eBlumat systems need constant low pressure — much less than municipal home and farm pressure. These reducers insure a constant pressure.\u003cbr\u003e\u003cbr\u003eOften, people call flow restrictors \"pressure reducers\" and they can reduce pressure — but only if the system has a high flow. These true pressure reducers take input an pressure up to 87 psi and drop it down to 15 psi (1 bar) output. Ideally suited for Blumat and other drip irrigation systems, lowering the pressure also prevents tubing connections from coming apart and creating a flood. \u003cbr\u003e\u003cbr\u003eIn gravity systems, you don't need a reducer unless you have a storage tank high up a hill, 35' or more vertical. Horizontal distance doesn't make much difference.\"\u003cbr\u003e\u003cbr\u003e3\/4\" Female Hose Thread input, 3\/4\" Male Hose Thread output, \u003cbr\u003eMax pressure in 87 psi, output pressure limited at 15 psi max\u003cbr\u003eA TRUE REDUCER - Not just a flow controller that only works with high flows, these reduce pressure in Blumat systems with extremely low flow rates\u003cbr\u003eEASY TO INSTALL - Uses standard 3\/4\" hose thread for both input and ouput sides\u003cbr\u003eHIGH QUALITY - Built to last from ABS plastic and designed for longest life \u003cbr\u003e\u003cbr\u003eBlumat systems need constant low pressure — much less than municipal home and farm pressure. These reducers insure a constant pressure.\u003cbr\u003e\u003cbr\u003eOften, people call flow restrictors \"pressure reducers\" and they can reduce pressure — but only if the system has a high flow. These true pressure reducers take input an pressure up to 87 psi and drop it down to 15 psi (1 bar) output. Ideally suited for Blumat and other drip irrigation systems, lowering the pressure also prevents tubing connections from coming apart and creating a flood. \u003cbr\u003e\u003cbr\u003eIn gravity systems, you don't need a reducer unless you have a storage tank high up a hill, 35' or more vertical. Horizontal distance doesn't make much difference.\u003cbr\u003e\u003cbr\u003e3\/4\" Female Hose Thread input, 3\/4\" Male Hose Thread output, \u003cbr\u003eMax pressure in 87 psi, output pressure limited at 15 psi max\u003c\/div\u003e","brand":"Sustainable Village","offers":[{"title":"Blumat Pressure Reducer 15 psi - 3\/4\" MHT output","offer_id":42916087431354,"sku":"IG18537","price":57.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0637\/4722\/7834\/products\/IG18537.all-01.jpg?v=1701909586"},{"product_id":"ig18687","title":"Blumat Pressure Reducer 7.5psi 3\/4\" MHT output","description":"\u003cdiv id=\"sv-product-tabs\"\u003e\n\u003ch5\u003eDescription\u003c\/h5\u003eLike our standard Blumat Pressure Reducer but with 3\/4\"\" hose thread output!\u003cbr\u003e\u003cbr\u003eThe standard Blumat pressure reducers work great for most systems. But for larger systems that need a higher flow rate, this becomes a better choice. This also works better when there's a long distance between the pressure reducer and your plants.\u003cbr\u003e\u003cbr\u003eA TRUE REDUCER - Not just a flow controller that only works with high flows, these reduce pressure in Blumat systems with extremely low flow rates\u003cbr\u003eEASY TO INSTALL - Uses standard 3\/4\"\" hose thread for both input and ouput sides\u003cbr\u003eHIGH QUALITY - Built to last from ABS plastic and designed for longest life \u003cbr\u003e\u003cbr\u003eBlumat systems need constant low pressure — much less than municipal home and farm pressure. These reducers insure a constant pressure.\u003cbr\u003e\u003cbr\u003eOften, people call flow restrictors \"pressure reducers\" and they can reduce pressure — but only if the system has a high flow. These true pressure reducers take input an pressure up to 87 psi and drop it down to 7.5 psi (.5 bar) output. Ideally suited for Blumat and other drip irrigation systems, lowering the pressure also prevents tubing connections from coming apart and creating a flood. \u003cbr\u003e\u003cbr\u003eIn gravity systems, you don't need a reducer unless you have a storage tank high up a hill, 35' or more vertical. Horizontal distance doesn't make much difference.\u003cbr\u003e\u003cbr\u003e3\/4\" Female Hose Thread input, 3\/4\" Male Hose Thread output, \u003cbr\u003eMax pressure in 87 psi, output pressure limited at 7.5 psi max\u003c\/div\u003e","brand":"Blumat GmbH \u0026 Co. KG","offers":[{"title":"Default Title","offer_id":42916145299642,"sku":"IG18687","price":53.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0637\/4722\/7834\/files\/140007.jpg?v=1760381539"},{"product_id":"ig18898","title":"Whole System Adjustable Pressure Reducer for Blumat systems","description":"\u003cdiv style=\"max-width: 680px; line-height: 1.7;\"\u003e\n  \u003cp style=\"font-size: 1.05rem; color: #3a3a3a; margin-bottom: 1.5rem;\"\u003eFull control over your Blumat system pressure. Adjustable from 2–14 PSI with a built-in gauge so you always know exactly what your system is running — the most important number to know in any Blumat setup.\u003c\/p\u003e\n\n  \u003cdetails style=\"border-top: 1px solid #d4c9b0; margin-bottom: 0;\"\u003e\n    \u003csummary style=\"cursor: pointer; padding: 1rem 0; font-size: 0.95rem; font-weight: 700; letter-spacing: 0.08em; text-transform: uppercase; list-style: none; display: flex; justify-content: space-between; align-items: center;\"\u003eKey Features \u003cspan style=\"font-size: 1.2rem; font-weight: 300;\"\u003e＋\u003c\/span\u003e\u003c\/summary\u003e\n    \u003cdiv style=\"padding-bottom: 1.2rem; color: #3a3a3a;\"\u003e\n      \u003cul style=\"margin: 0; padding-left: 1.2rem; line-height: 2;\"\u003e\n        \u003cli\u003eBuilt-in 0–30 PSI pressure gauge for real-time monitoring\u003c\/li\u003e\n        \u003cli\u003eHigh flow rate of over 5 gallons per minute — can replace six or more standard Blumat pressure reducers\u003c\/li\u003e\n        \u003cli\u003eAdjustable from 2–14 PSI to match any distribution method (drippers, drip rings, BluSoak)\u003c\/li\u003e\n        \u003cli\u003ePowerful enough for the largest systems, precise enough for single-zone setups\u003c\/li\u003e\n      \u003c\/ul\u003e\n    \u003c\/div\u003e\n  \u003c\/details\u003e\n\n  \u003cdetails style=\"border-top: 1px solid #d4c9b0; margin-bottom: 0;\"\u003e\n    \u003csummary style=\"cursor: pointer; padding: 1rem 0; font-size: 0.95rem; font-weight: 700; letter-spacing: 0.08em; text-transform: uppercase; list-style: none; display: flex; justify-content: space-between; align-items: center;\"\u003eConnections \u0026amp; Adapters \u003cspan style=\"font-size: 1.2rem; font-weight: 300;\"\u003e＋\u003c\/span\u003e\u003c\/summary\u003e\n    \u003cdiv style=\"padding-bottom: 1.2rem; color: #3a3a3a;\"\u003e\n      \u003cp style=\"margin: 0 0 0.8rem;\"\u003eThe reducer body has a ½\" male pipe thread (MPT) inlet and a ¾\" female pipe thread (FPT) outlet. Included adapters make it easy to install:\u003c\/p\u003e\n      \u003cul style=\"margin: 0; padding-left: 1.2rem; line-height: 2;\"\u003e\n        \u003cli\u003e\n\u003cstrong\u003eInput\u003c\/strong\u003e — ¾\" PVC swivel adapter for standard garden hoses or hose bibs\u003c\/li\u003e\n        \u003cli\u003e\n\u003cstrong\u003eOutput — ¾\" to ½\" Perma-Loc fitting\u003c\/strong\u003e for Trunk Line Kits\u003c\/li\u003e\n        \u003cli\u003e\n\u003cstrong\u003eOutput — ¾\" to 8mm adapter\u003c\/strong\u003e for Supply Line Kits with SuperFlex tubing\u003c\/li\u003e\n        \u003cli\u003e\n\u003cstrong\u003eAlso includes\u003c\/strong\u003e — ¾\" FPT tee and 1\/4\" to ¾\" MBT bushing\u003c\/li\u003e\n      \u003c\/ul\u003e\n    \u003c\/div\u003e\n  \u003c\/details\u003e\n\n  \u003cdetails style=\"border-top: 1px solid #d4c9b0; margin-bottom: 0;\"\u003e\n    \u003csummary style=\"cursor: pointer; padding: 1rem 0; font-size: 0.95rem; font-weight: 700; letter-spacing: 0.08em; text-transform: uppercase; list-style: none; display: flex; justify-content: space-between; align-items: center;\"\u003eInstallation Instructions \u003cspan style=\"font-size: 1.2rem; font-weight: 300;\"\u003e＋\u003c\/span\u003e\u003c\/summary\u003e\n    \u003cdiv style=\"padding-bottom: 1.2rem; color: #3a3a3a;\"\u003e\n      \u003col style=\"margin: 0; padding-left: 1.2rem; line-height: 2;\"\u003e\n        \u003cli\u003eTape all male fittings with the provided tape, wrapping 5–6 times clockwise.\u003c\/li\u003e\n        \u003cli\u003eAssemble parts as pictured in the instruction diagram.\u003c\/li\u003e\n        \u003cli\u003eConnect to a valve on a pump kit or to a hose bib using the provided ¾\" swivel adapter.\u003c\/li\u003e\n        \u003cli\u003eUsing the provided fittings, connect to your Blumat system supply line.\u003c\/li\u003e\n        \u003cli\u003eOpen the incoming water to check current system pressure. Recommended ranges:\n          \u003cul style=\"margin: 0.4rem 0 0; padding-left: 1.2rem; line-height: 2;\"\u003e\n            \u003cli\u003eDrip rings — 12–15 PSI\u003c\/li\u003e\n            \u003cli\u003eBluSoak — 7–10 PSI\u003c\/li\u003e\n          \u003c\/ul\u003e\n        \u003c\/li\u003e\n        \u003cli\u003eTo adjust pressure: turn off incoming water, release system pressure by opening a valve on the Blumat supply line until the gauge reads 0, then turn the black adjustment collar (tighten for more pressure, loosen for less).\u003c\/li\u003e\n        \u003cli\u003eClose the Blumat supply line valve and open incoming water to re-pressurize. Check the gauge. If not in range, repeat steps 6–7 until correct.\u003c\/li\u003e\n      \u003c\/ol\u003e\n    \u003c\/div\u003e\n  \u003c\/details\u003e\n\n  \u003cdiv style=\"border-top: 1px solid #d4c9b0;\"\u003e\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Sustainable Village","offers":[{"title":"Default Title","offer_id":42916219289786,"sku":"IG18898","price":126.36,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0637\/4722\/7834\/files\/143713.jpg?v=1760381738"}],"url":"https:\/\/sustainablevillage.com\/collections\/pressure-reducers.oembed","provider":"Sustainable Village","version":"1.0","type":"link"}